Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Table of contents
1
Introduction ........................................................
2
Product description (Fig. 1-28)...........................
3
Scope of delivery (Fig. 2) ...................................
4
Proper use..........................................................
5
Safety instructions..............................................
6
Technical data....................................................
7
Unpacking ..........................................................
8
Assembly............................................................
9
Before commissioning........................................
10 Commissioning...................................................
11 Working instructions...........................................
12 Electrical connection ..........................................
13 Transport............................................................
14 Maintenance and cleaning .................................
15 Storage...............................................................
16 Repair & ordering spare parts ............................
17 Disposal and recycling .......................................
18 Troubleshooting .................................................
19 EU Declaration of Conformity.............................
20 Exploded view .................................................... 195
Explanation of the symbols on the
product
Symbols are used in this manual to draw your attention to
potential hazards. The safety symbols and the accompa-
nying explanations must be fully understood. The warn-
ings themselves will not rectify a hazard and cannot re-
place proper accident prevention measures.
Before com-
missioning,
read and ob-
serve the oper-
ating manual
and safety in-
structions!
Wear safety
goggles.
Wear hearing
protection.
If dust builds
up, wear respi-
ratory protec-
tion!
WARNING!
Danger of inju-
ry! Do not
reach into
sanding disc
while it is run-
ning!
18 | GB
18
18
19
1
19
Manufacturer:
19
Scheppach GmbH
21
Günzburger Straße 69
21
D-89335 Ichenhausen
22
Dear Customer
22
We hope your new product brings you much enjoyment
22
and success.
23
Note:
24
In accordance with the applicable product liability laws,
the manufacturer of this product assumes no liability for
24
damage to the product or caused by the product arising
25
from:
25
• Improper handling
25
• Non-compliance with the operating manual
25
• Repairs carried out by third parties, unauthorised spe-
26
26
• Installing and replacing non-original spare parts
• Improper use
• Failures of the electrical system in the event of the
Note:
The operating manual is part of this product.
It includes important instructions for the safe, proper and
economic operation of the product, for avoiding danger,
for minimising repair costs and downtimes and for in-
creasing the reliability and extending the service life of the
product. In addition to the safety instructions in this oper-
ating manual, you must also observe the regulations ap-
Running direc-
plicable to the operation of the product in your country.
tion/grinding
belt size
Familiarise yourself with all operating and safety instruc-
tions before using the product. Only operate the product
as described and for the specified areas of application.
Keep the operating manual in a good place and hand
over all documents when passing the product on to third
Grinding belt
parties.
size and speed
2
Sanding disc
1.
2.
size
3.
3a.
4.
Table adjust-
4a.
ment angle
4b.
scale
4c.
5.
6.
The product
7.
complies with
7a.
the applicable
8.
European di-
9.
rectives.
10.
11.
www.scheppach.com
Running direc-
tion of the
sanding disc
Introduction
cialists
electrical regulations and VDE provisions 0100, DIN
57113 / VDE0113 not being observed.
Product description (Fig. 1-28)
Knurled screw for grinding belt adjustment
Grinding belt tensioner
Sanding wheel
Sanding wheel P80 sandpaper (pre-assembled)
Control panel
On/off switch
Speed control
Display
Transverse stop
Sanding table
Locking screw for sanding table
Washer
Suction port
Base plate
Mounting hole
Allen screw
Werbung
