Herunterladen Diese Seite drucken

Scheppach PGS75 Originalbetriebsanleitung Seite 33

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Check the oil level regularly before commissioning. An
oil level that is too low can damage the motor.
1. Unscrew the oil filler cap with oil dipstick (16).
2. Use a funnel to top up the engine oil. Note the max.
filling capacity of 0.55 l. Fill the oil up to the lower
edge of the filling nozzle carefully.
3. Wipe the oil filler cap with oil dipstick (16) with a
clean, lint-free cloth.
4. Screw the oil filler cap with oil dipstick (16) back into
the filling nozzle until it reaches the stop.
5. Unscrew the oil filler cap with oil dipstick (16) and
read the oil level in the horizontal position. The oil
level must be in the middle on the oil filler cap with
oil dipstick (16).
6. If the oil level is too low, repeat the process.
7. Then screw the oil filler cap with oil dipstick (16)
back in.
9.2
Filling in fuel (Fig. 8)
ATTENTION
The product is delivered without fuel. It is
therefore essential to fill with fuel before
commissioning. Use Super E5 petrol for
this.
1. Unscrew the fuel filler cap (3).
2. Use a suitable funnel to fill a maximum of 3.6 l of E5
unleaded petrol into the fuel tank (4).
3. Ensure that the fuel tank (4) is not overfilled and that
no fuel is spilled. Always use the fuel filter insert
(17). Wipe up spilled fuel immediately and wait until
the fuel vapours have evaporated (risk of ignition).
4. Retighten the fuel filler cap (3).
10 Operation
ATTENTION
Attention!
When using products, several safety warnings must
be observed to prevent injuries and damage. For this
reason, please carefully read this operating manual /
safety instructions. If you hand the product over to an-
other person, please hand over this operating manu-
al / safety instructions as well. We accept no liability
for accidents or damage that occur due to a failure to
observe this manual and the safety instructions.
ATTENTION
Always make sure the product is fully assembled
before commissioning!
ATTENTION
Always check whether the feed funnel is empty and
that the blades are not blocked prior to starting the en-
gine!
ATTENTION
Remaining in the petrol impact garden shredder's dan-
ger area when starting and operating is prohibited.
WARNING
Check the safety equipment regularly before each
start-up. Faulty safety equipment can cause serious
injuries!
Note:
• Good work results require well sharpened blades.
• Blunt blades reduce the cutting performance and im-
pair the work process! Sure signs of blunt blades are
leaving an indentation, reduced performance and a
poor cutting pattern.
• Always stand to the side of the filling funnel when
feeding chopped material (Fig. 16)
Speeds
Use the throttle lever (21) to set the engine to the de-
sired speed.
• MIN position, "tortoise"
• MAX position, "hare"
10.1
Starting the engine (5) (Fig. 9)
DANGER
Danger of poisoning!
Only use the product outdoors and never in closed or
poorly ventilated rooms.
ATTENTION
Do not allow the pull starter to recoil. This can re-
sult in damage.
In case of cool weather, it may be necessary to re-
peat the starting process numerous times.
Note:
If the engine is cold, set both the choke lever and the fu-
el valve to the "ON" position. If the engine is warm, the
choke is not required.
1. Set both the choke lever (19) and the fuel valve (20)
on the engine to "ON".
2. Position the throttle (21) in the middle.
3. Turn the on/off switch (18) to "ON".
www.scheppach.com
GB | 33

Werbung

loading

Diese Anleitung auch für:

59044069953