Scheppach PGS75 Originalbetriebsanleitung Seite 32

8.2 Fitting the shredding unit (12)
(Fig. 4)
1. Position the shredding unit (12) over the base frame
(7) and ensure that the fitting holes are aligned.
2. Fasten the shredding unit (12) to the base frame (7)
with four M8x35mm screws (D), M8 spring washers
(E), M8 washers (F) and M8 locknuts (G). Use two
13 mm open-ended spanners/socket spanners to fit
the M8x35mm screws (D).
8.3 Mounting the feed funnel (2)
(Fig. 5)
1. Position the feed funnel (2) with the feed funnel rub-
ber seal (H) over the shredding unit (12) and ensure
that the fitting holes are aligned.
2. Fasten the feed funnel (2) to the shredding unit (12)
with three M6x16mm screws (I), M6 spring washers
(J), M6 washers (K). Use a 10 mm socket spanner/
open-ended spanner to fit the M6x16mm screws (I).
8.4 Connecting the loading funnel
safety switch (14) /catch basket
safety switch (8) (Fig. 1, 5)
1. Connect the loading funnel safety switch cable (14)
to the engine connection cable (15).
2. Repeat the procedure for the catch basket safety
switch (8).
8.5 Fitting the transport handle (1)
(Fig. 6)
1. Position the transport handle (1) with the narrow side
on the inside of the feed funnel (2).
2. Fasten the transport handle (1) to the feed funnel (2)
with four M6x20mm screws (L), M6 spring washers
(J), M6 washers (K). Use a 10 mm socket spanner/
open-ended spanner to fit the M6x20mm screws (L).
8.6 Inserting the catch basket (10)
(Fig. 7)
1. Slide the catch basket (10) along the guide rail into
the base frame (7).
Note:
The petrol impact garden shredder can only be started
once the collection bucket has been pushed into the
base frame correctly.
9 Before commissioning
ATTENTION
Always make sure the product is fully assembled
before commissioning!
Note:
Place the product on a level, even surface.
32 | GB
WARNING
Health hazard!
Inhalation of fuel / lubricating oil vapours and exhaust
gases can cause serious damage to health, uncon-
sciousness and in extreme cases death.
– Do not breathe fuel / lubricating oil vapours and
exhaust gases.
– Operate the product outdoors only.
ATTENTION
Product damage!
Using the product without or with too little engine and
gear oil can result in engine damage.
– Fill with fuel and oil before starting the machine.
The product is supplied without engine and gear-
box oil.
ATTENTION
Environmental damage!
Spilled oil can pollute the environment permanently.
The liquid is highly toxic and can quickly lead to water
pollution.
– Fill/empty oil only on level, paved surfaces.
– Use a filling nozzle or funnel.
– Collect drained oil in a suitable container.
– Wipe up spilled oil carefully immediately and dis-
pose of the cloth according to local regulations.
– Dispose of oil as per local regulations.
ATTENTION
Risk of damage!
If incorrectly stored or undrained fuel is used, the car-
burettor may become clogged or engine operation
may be affected.
– Put unused fuel in an airtight vessel and store it in
a dark, cool room.
Tool required:
* Not included in the scope of delivery!
• Funnel*
• Cloth*
9.1 Topping up oil (Fig. 8)
ATTENTION
The product is delivered without engine oil. There-
fore, ensure that you add oil before starting it up.
Use SAE 10W-40 oil.
www.scheppach.com