Technical Data; Assembly; Putting Into Operation - Scheppach GS45 Original Bedienungsanleitung

Remaining hazards
The machine has been built using modern technology
in accordance with recognized safety rules. Some
operating hazards, however, may still exist.
• Even if used properly, residual risks can exist even
if the relevant safety regulations are complied with
due to the design determined by the intended pur-
pose.
• Observing these instructions, and taking proper
care, will reduce the risk of personal injury or dam-
age to the equipment.
• Risk of injury to the fingers and hands, if your hand
grasps through an opening and reaches the blade
unit.
• Risk of injury to the fingers and hands, when car-
rying out assembly work and cleaning on the blade
unit.
• Touching live parts of opened electrical compo-
nents.
• Injury caused by kick-back of branches while feed-
ing. Securely hold long,thick branches. Wear per-
sonal protective gear such as gloves and safety
goggles.
• Health risks caused by noise. Wear personal pro-
tective gear (ear protection)
• Health risks caused by electricity. When incorrect
or damaged mains cables are used. Follows in-
structions in the manual Electrical Connections.
• Even when all safety measure are taken, some
maining hazards which are not yet evident may still
be present.
• Remaining hazards can be minimized by following
the instructions in Safety Precautions, Proper Use
and in the entire operating manual.

7. Technical Data

Dimensions L x B x H (mm)
Input height (mm)
Output height (mm)
Infeed opening max. (mm)
Outfeed opening max.
(mm)
Wheel ø (mm)
Weight (kg)
Branch thickness max. ø
(mm)
Blade disc ø (mm)
Saw blde (mm)
Motor (V/Hz)
Consumtion power P1 (W)
Revolutions (1/min )
-1
Operation mode
Splashproof
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
490 x 370 x 860
860
45
40
45
165
10,7
40
171
72 x 29 x 5,3
230/50
2000
4500
S6/40 %
IP X4
Subject to technical changes!
Noise Information
Sound emission values determined according to EN
ISO 3744:2010, EN11201:2010
Typically the A-weighted noise levels of the product
are: Sound pressure level 96,7 dB (A);
Sound power level 104,5 dB (A).
2000/14 / EC: the guaranteed sound power level LwA
is lower than 106 dB (A). Assessment procedure of
conformity according to Annex V.

8. Assembly

Your garden shredder is not fully assembled due to
technical packing difficulties.
m ATTENTION! Always make sure the device is
fully assembled before start-up!
1. Open the box and remove the machine and all of
its accessories.
2. Mounting the subframe (Fig. 3)
• First rotate the upper section of machine (3)
(Fig. 3).
• Insert the subframe (4) into the holes provided
(3a) as seen in the Figure.
3. Mounting the idlers (Fig. 4)
• Fit the two idlers ( 5) as shown in Fig. 4 and 5.

9. Putting into operation

Observe safety notes before putting into operation.
The machine may only be operated with fully mount-
ed protection and infeed system.
Starting protection
Your garden shredder can only be started when the
top of the housing is correctly closed. The locking
screw is simultaneously the screw which fastens the
upper and lower housing unit together and the secu-
rity nut for the starting safeguard. In tightening the
screw to the stud (1), contact is made to the circuit
breaker and the circuit closer. The motor starts when
the on-button is pressed. If the screw is not quite
screwed in or the housing is open, the electric circuit
is interrupted by the starting safeguard. In pressing
the on-button, the motor should not start.
Switching on/off
• The machine can be switched on by pressing the
button to „I".
• In order to switch the machine off again, press the
button to „0".