Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DANGER
Risk of fire and explosion!
When filling, fuel may ignite and even explode. This
can lead to severe burns or death.
• Only store fuel in containers (canisters) designed for
this purpose.
• The tank caps must always be properly screwed on
and tightened.
• Fuel must be filled before starting the engine. While
the engine is running or immediately after switching
off the product, do not open the fuel filler cap or add
fuel.
• Before refuelling, switch off the combustion engine
and let it cool down.
• Refuel outdoors only and do not smoke while refuel-
ling.
• Never store the product with fuel in the tank inside a
building. Any fuel vapours produced can come into
contact with naked flames or sparks and ignite.
• Do not place the product and fuel tank near heaters,
radiant heaters, welding machines or other sources
of heat.
• If fuel has overflowed, do not start the combustion
engine until the area contaminated with fuel has
been cleaned. Avoid starting the engine until the fuel
vapours have evaporated (wipe dry).
• For safety reasons, check fuel line, fuel tank, fuel
cap and connections regularly for damage, ageing
(brittleness), tight fit and leaks and replace if neces-
sary.
5.2
Handling
• Before starting the machine, make sure that the fill-
ing funnel is empty.
• Keep your head and body a safe distance from the
loading slot.
• Do not place hands, other parts of the body and
clothing in the filling chamber, the ejector chute or in
the vicinity of other moving parts.
• Always pay attention to your balance and firm foot-
ing. Do not bend over or stand higher than the de-
vice when throwing material in.
• Always stay outside of the ejection zone when com-
missioning the machine.
• Ensure that hard objects such as metal, stones,
glass or other foreign objects are not contained in
the material being thrown in.
• If foreign objects get into the cutting tool or the ma-
chine makes unusual noises or vibrates abnormally,
switch the engine off immediately and allow the ma-
chine to run down. Remove the spark plug connector
and perform the following steps:
– Check the machine for damage
30 | GB
– Check the parts for firm seating, retighten them if
necessary.
– Repair or replace any damaged parts with parts
that are of equivalent quality
• Do not let processed material pile up within the ejec-
tion area; this could prevent proper ejection and
cause a kick-back of the material through the filling
funnel.
• In the event of blockages in the loading or ejection
area of the machine, switch the engine off and pull
the spark plug connector before removing material
remaining in the loading slot or ejector chute.
• Make sure that the engine is free of waste and other
accumulations to safeguard the engine from damage
or possible fire.
• Remember that when the starter mechanism with
motorised machines is commissioned, the cutting
tool also starts operating.
• Make sure all covers and deflectors are in their place
and in good working condition.
• Do not change the speed governor setting of the en-
gine or over-rev it. The safe maximum working
speed regulates the speed and protects the engine
and all rotating parts from damage due to excess
speed. Contact customer service if you have any
problems.
• Do not transport or tilt the device with the engine
running.
• Switch the engine. off and pull out the spark plug as
soon as you leave your workstation.
5.3
Residual risks
The product has been built according to state-of-
the-art and the recognised technical safety rules.
However, individual residual risks can arise during
operation.
• Residual risks can be minimised if the "Safety In-
structions" and the "Intended Use" together with the
operating manual as a whole are observed.
• Use the product in the way that is recommended in
this operating manual. This is how to ensure that
your product provides optimum performance.
• Prevent the product being unintentionally started up.
• Keep your hands away from the working area when
the product is in operation.
• Comply with the stipulated maintenance and safety
instructions in the operating manual.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
6
Technical data
Dimensions L x W x H
Infeed height
Infeed opening max.
www.scheppach.com
943 x 673 x 1063 mm
900 mm
250 x 250 mm
Werbung
