Herunterladen Diese Seite drucken

Viessmann 5242 Gebrauchsanleitung Seite 5

Miniatur lokdecoder mit lastregelung

Werbung

genschaften des Motors angepassten, Geschwin-
digkeitskennlinie. Die eingestellten Werten werden
in der alternativen Geschwindigkeitstabelle abge-
speichert (CV 67 - 94).
Rangiergang
Der Rangiergang halbiert die Geschwindigkeit al-
ler Fahrstufen gegenüber der eingestellten Ge-
schwindigkeit.
Anfahr- und Bremsverzögerung
Die Anfahr- und die Bremsverzögerung sind ge-
trennt voneinander programmierbar.
Nothalt
Bei entsprechender Programmierung wird bei
einem Richtungswechsel automatisch ein Nothalt
ausgeführt.
Funktions- bzw. Lichtausgänge
Zwei Funktions- bzw. Lichtausgänge (max. Strom
je 100 mA) ermöglichen den Anschluss von Ver-
brauchern (z. B. Licht, Signalhorn). Der maximale
Gesamtstrom des Decoders (einschließlich Motor-
strom) beträgt 700 mA.
Die Ausgänge werden im DCC-Format über die
Funktionstasten F0 bis F12 geschaltet. Im Moto-
rola-Format werden die Ausgänge über die Funk-
tionstasten F0 bis F4 geschaltet. Die Funktionen
F5 bis F9 können über die Funktionstasten F1 bis
F4 und F0, die einer zweiten Decoderadresse zu-
geordnet werden, geschaltet werden. Die Funk-
tionen F10 bis F12 stehen im Motorola-Format
nicht zur Verfügung.
Die Zuordnung der Funktionstasten zu den Funk-
tionsausgängen des Decoders ist frei wählbar. Sie
können einem Funktionsausgang mehrere Funkti-
onstasten zuordnen.
Effekte der Funktionsausgänge
Für alle Funktionsausgänge können einzeln die
folgenden Effekte eingestellt werden:
Dimmfunktion: Die Ausgangsspannung ist durch
entsprechende Programmierung reduzierbar.
Anwendungs b eispiel: Die für den Analogbetrieb
vorgesehenen Birnen älterer Fahrzeuge können
gedimmt werden und müssen dann nach dem
Einbau des Decoders nicht ausgetauscht werden.
Außerdem kann die Spannung in Abhängigkeit
von der Fahrstufe gedimmt werden.
Blinkfunktion: Frequenz und Tastverhältnis der
Blinklichter lassen sich einstellen.
Fahrtrichtungsabhängiges Schalten: Jeder
Ausgang kann so programmiert werden, dass er in
Abhängigkeit von der Fahrtrichtung geschaltet wird.
the linear velocity characteristic. This allows the
programming of a velocity characteristic which
adjusts the individual driving characteristics of the
motor. The set values are saved in the alternative
velocity table (CV 67 - 94).
Shunting gear
In the shunting gear mode, the velocity of all
speed levels is reduced to approx. 50 % com-
pared to the set velocity.
Acceleration and brake delay
It is possible to program the acceleration and
brake delay individually via the central unit.
Emergency stop
At a change of direction an emergeny stop is car-
ried out automatically.
Function resp. light outputs
The decoder has two function outputs with a
maximum current of 100 mA each, which are
available to connect optional accessories (e.g.
lighting, smoke generator, sound module, electric
coupling). The decoder´s maximum total current
(including motor current) is 700 mA.
In DCC format the function outputs can be
switched via the function keys F0 to F12. In Mo-
torola format the function outputs can be switched
via the function keys F0 to F4. The functions F5 to
F9 can be switched via the function keys F1 to F4
and F0 by assigning them to a second address.
The functions F10 to F12 are not available in Mo-
torola format.
You can assign the function keys to the function
outputs freely. It is possible to assign several func-
tion keys to one function output.
Effects of the function outputs
It is possible to set the following effects for all
function outputs individually:
Dimming: The voltage applied to an output can
be reduced by programming the decoder accord-
ingly.
Example of use: The electric bulbs of older vehi-
cles made for analogue operation can be dimmed
and thus must not be exchanged after the mount-
ing of the decoder. In addition, it is possible to dim
the voltage depending on the speed level.
Flashing: Both the frequency and the keying ratio
can be set. Examples of use: single and alternat-
ing flash lights or strobe lights.
Switching on and off depending on the direc-
tion of travel: Any output can be programmed to
be switched on and off depending on the direction
of travel.
5

Werbung

loading

Diese Anleitung auch für:

5243