Behringer MS-1 Schnellstartanleitung Seite 19

Control Section
VOLUME – adjust the volume level of the
(31)
main output and headphones output. Turn
this down before turning the power on, or
before putting on headphones.
GLIDE – adjust the amount of Glide time
(32)
(Portamento) between notes on the keyboard.
GLIDE ON/OFF – turn the GLIDE on or off.
(33)
TRANSPOSE – adjust the keyboard in one
(34)
octave steps, from Low, Medium, and High.
VCO FADER – adjust the effect of the bender
(35)
controls on the VCO.
VCF FADER – adjust the effect of the bender
(36)
controls on the VCF.
LFO MOD FADER – adjust the amount of LFO
(37)
modulation added when the MOD switch
on the grip is pressed, or the BENDER (38) is
moved up.
BENDER – move left or right to adjust the
(38)
frequency of the VCO and/or the cut-off
frequency of the VCF. The level of the effect
depends on the setting of the nearby VCO and
VCF faders. Move it up to add LFO modulation.
The modulation effect depends upon the
setting of the LFO MOD fader and other
LFO controls.
Rear Panel
DC INPUT – connect the supplied DC
(39)
power adapter here. The power adapter
can be plugged into an AC outlet capable of
supplying from 100V to 240V at 50 Hz/60 Hz.
Use only the power adapter supplied.
MAIN OUTPUT – connect this output to
(40)
the line-level inputs of mixers, keyboard
amplifiers, or powered speakers for example.
PHONES – connect your headphones to this
(41)
output. Make sure the volume is turned down
before putting on headphones.
EXT AUDIO INPUT – this input can be
(42)
connected to the line level audio output from
an external audio device. Adjust the level
using the EXT AUDIO fader in the SOURCE
MIXER section.
HOLD – an optional footswitch can be
(43)
connected here, to hold or release any
pattern playing in the Sequencer, and in
normal performance.
VCF CV INPUT – the VCF can be controlled by
(44)
an external control voltage connected here.
EXT CLK INPUT – an external clock signal can
(45)
be applied here.
CV/GATE INPUT – these inputs allow the
(46)
connection of control voltage and gate signals
from compatible external devices such as
modular synthesizer equipment.
CV/GATE OUTPUT – these outputs allow
(47)
the connection of control voltage and gate
signals to compatible external devices such as
modular synthesizer equipment.
VELOCITY OUT – outputs a variable control
(48)
voltage based on the key velocity.
MIDI Connections – these 3 standard 5-pin
(49)
DIN Jacks allow connections to other MIDI
equipment in your system.
MIDI IN – receives MIDI data from an external
source. This will commonly be another MIDI
keyboard, an external hardware sequencer, a
computer equipped with a MIDI interface, etc.
MIDI THRU – passes through MIDI data
received at the MIDI INPUT.
MIDI OUT – sends MIDI data to an application
USB PORT – This USB type B jack allows
(50)
connection to a computer. The MS-1 will show
up as a class-compliant USB MIDI device,
capable of supporting MIDI in and out.
USB MIDI IN – accepts incoming MIDI data
from an application.
USB MIDI OUT - sends MIDI data to an
application.
GRIP/ MOD – the connector
(51)
of the live performance grip attaches here.
Quick Start Guide
Live Performance Kit
BENDER – adjusts the frequency of the VCO
(52)
and/or the cut-off frequency of the VCF. The
level of the effect depends on the setting of
the VCO and VCF Bender faders. This control
only increases the frequency. The main unit
bender can also be used at the same time.
MOD – press and hold to add LFO modulation.
(53)
The level of effect depends upon the setting of
the LFO mod fader, and the other LFO controls.
CONNECTOR – fit into the GRIP and MOD
(54)
connectors in the main unit rear panel.
MOUNTING HOLES – fit the supplied screws
(55)
in these holes to secure the handle to the left
side of the main unit.
STRAP POINT 1 – connect one end of the
(56)
supplied strap here.
STRAP POINT 2 – secure this to the right side
(57)
of the main unit with the supplied screws.
STRAP – the supplied strap attaches to the 2
(58)
strap points.
19