AERMEC FCW 212V Bedienungsanleitung Seite 38

AUTOMATIC pROGRAMME (AUTO)
The programme requires the system to circulate chilled or hot water.
1) pRESS THE ON/Off OR
The fan coil unit comes on. The fan coil unit will automatically switch on in Cool
mode, Heat mode or in the dead band (waiting) depending on the water temperature.
2) pRESS THE MODE kEy
Press the MODE key repeatedly until the word AUTO appears on the display
(TLW2) or the LEDs on wired control panel (PFW2) turns on HEAT and COOL.
3) pRESS THE fAN OR
When the FAN key is pressed repeatedly, the system can move to the minimum speed
(LOW), medium speed (MED) and high speed (HIGH) or to the (AUTO) speed con-
trolled by the microprocessor.
OR
4) pRESS THE
– The key with the symbol
– The key with the symbol
The display shows the set point value between 16 and 30 °C.
5) TO DIRECT THE AIR fLOw
To ensure optimum air distribution, adjust the horizontal blades and the vertical
blades in such a way that the air flow does not hit people directly. The vertical air
flow blades must be set manually before starting up the motorised blades.
Never adjust the motorised horizontal blades manually.
When the LOUVER key is pressed repeatedly, the horizontal blade is adjusted to 4
fixed blade positions, then a swinging blade movement will begin. If you wish to
stop the blade in a particular position, press the LOUVER key.
When the SWING key is pressed a swinging blade movement will begin. If you
wish to stop the blade in a particular position, press the SWING key again.
6) pRESS THE SEND kEy (TLw2)
To transmit the new parameters shown on the LCD to the main control unit.
wHAT HAppENS wHEN THE AUTOMATIC pROGRAMME IS SET
With AUTO programme, the control system decides the type of operation (COOL
or HEAT) on the basis of the water and room temperature and set point.
HEATING pROGRAMME (HEAT)
The programme requires the system to circulate hot water.
1) pRESS THE ON/Off OR
The fan coil unit comes on and the display on the unit switches on.
2) pRESS THE MODE kEy
Press the MODE key repeatedly until the word HEAT appears on the display (TLW2)
or the LEDs on wired control panel (PFW2) turns on HEAT.
3) pRESS THE OR
– The key with the symbol
– The key with the symbol
The display shows the set point value between 16 and 30 °C.
4) pRESS THE fAN OR
When the FAN key is pressed repeatedly, the system can move to the minimum speed
(LOW), medium speed (MED) and high speed (HIGH) or to the (AUTO) speed con-
trolled by the microprocessor.
5) TO DIRECT THE AIR fLOw
To ensure optimum air distribution, adjust the horizontal blades and the vertical
blades in such a way that the air flow does not hit people directly. The vertical air
flow blades must be set manually before starting up the motorised blades.
Never adjust the motorised horizontal blades manually.
When the LOUVER key is pressed repeatedly, the horizontal blade is adjusted to 4
fixed blade positions, then a swinging blade movement will begin. If you wish to
stop the blade in a particular position, press the LOUVER key.
When the SWING key is pressed a swinging blade movement will begin. If you
wish to stop the blade in a particular position, press the SWING key again.
6) pRESS THE SEND kEy (TLw2)
To transmit the new parameters shown on the LCD to the main control unit.
38
IFCW3LJ 1210 - 5375700_01
kEyS
kEyS
kEyS TO SET THE TEMpERATURE
allows increases of 1°C
allows decreases of 1°C
kEyS
kEyS TO CONTROL THE TEMpERATURE
allows increases of 1°C
allows decreases of 1°C
kEyS
6
TLW2
PFW2
6
TLW2
PFW2