Commissioning - Scheppach 5901802915 Original Bedienungsanleitung

The dimensions on the scale for depth of cut (2)
shows the cutting depth without rail.
Adjusting the cutting angle between 0° and 45°
(Fig. G)
The mitre square can be set from 0° to 45°.
Unscrew the mitre adjustment screws (14) on both
sides.
Swivel the sawing unit to the desired cutting angle
(Scale for mitre square (6)).
Tighten the mitre adjustment screws (14) on both
sides.
Note: Both positions (0° and 45°) are set at the fac-
tory and can be readjusted by the after-sales service
team.
Changing the saw blade (Fig. A-D, H, I)
m CAUTION! Risk of injury! Hot and sharp tools
Do not use insert tools that are blunt or defective.
Wear protective gloves.
m Warning! Risk of injury! Electric shock
Always pull the mains plug out of the socket before
performing any type of work on the machine!
1. Press the plunge trigger (3), bring the saw blade
into the blade-change position (Adjustment screw
for depth of cut (7) shall be adjusted to 25 mm)
and insert the hex wrench into the saw blade lock-
ing screw (19).
2. Press on the shaft lock (18) and rotate the saw
blade (15) until the lock clicks into place.
3. Hold down the locking shaft (18) and open the saw
blade locking screw (19) counter clockwise, while
keeping the blade in the blade-changing position.
4. Remove the outer flange (20) and the saw blade
(15).
m
Caution! Risk of injury!
Wear protective gloves
5. Insert the new blade and outer flange (20).
6. Screw in and tighten the saw blade locking screw
(19) while keeping the shaft locking mechanism
pressed again.
7. Set the plunge saw to its original position (0°).
Adjusting the riving knife (16) (Fig. A + K)
Adjust the distance between saw blade (15) and riv-
ing knife (16) after a saw blade replacement, or when-
ever necessary.
Put the saw in the same position as you do when re-
placing a saw blade.
30 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Unfasten the adjustment screw for riving knife (17)
using an Allen key and set the riving knife (16) 2-3
mm higher than the saw blade, then re-tighten the
adjustment screw for riving knife (17).
Connecting extraction device
A normal household vacuum cleaner is not a suitable
extraction device.
A extraction device with an extractor hose diameter
of 38 mm (38 mm recommended due to the reduced
risk of clogging) can be connected to the extractor
connector (1).
m Warning! Dust hazard
Dust can be hazardous to health. Always work with a
dust extractor.
Always read applicable national regulations before
extracting hazardous dust.

9. Commissioning

m
Warning! Risk of injury!
Improper assembly of the plunge saw can result in
serious injury.
• Before switching the plunge saw on, make sure
the saw blade is correctly mounted and that mobile
parts can move freely.
After switching on the saw, you must wait until the
saw blade (15) has reached the maximum speed be-
fore you perform the cut.
Switching the plunge saw on and off
• To switch on the plunge saw, press the ON/OFF
switch (8). The motor will start.
• To switch off the plunge saw, release the ON/OFF
switch (8).
After having performed all the above procedures and
opera tions, you may begin cutting.
m
Caution!
Always keep hands away from the cutting area and
do not try to approach it when the machine is running.
Working with the machine
m ATTENTION! Please observe all mentioned safe-
ty informations and the following rules when working:
• Only guide the machine against the workpiece
when it is switched on.
• Always secure the workpiece in such a manner that
it cannot move while being processed.
• Always push the machine forwards, never draw the
machine towards yourself.
• Adapt the fast-feed speed to prevent the cutters on
the saw blade from overheating and prevent plastic
materials from melting during cutting.
• For work that generates dust, wear a dust mask.