Submenu » Location Database; Submenu » Change Current Location; Submenu » Data Entry; Submenu » Set Date And Time - Dräger Alcotest 9510 Standard IR Gebrauchsanweisung

Menu
6.2.6 Submenu » Location Database «
In this submenu additional
locations can be created for
selection when performing
measurements. They
shown on the screen and
printed on the measurement
protocol.
1. Select the desired location field.
2. Enter the location.
3. Accept the entry with Confirm. The return to the menu is
automatic.
The maximum admissible length of an entry is 17 characters.
A maximum of 10 locations can be entered.
6.2.7 Submenu » Change Current Location «
In this submenu, you can select
the location, which is to be
indicated in the second line of
the display.
1. Select the desired location.
The selected location is
highlighted by a selection
marker.
2. Accept the entry
Confirm. Return to the
menu is automatic.
The selected location appears on the display and is
included when printing the measuring report.
6.2.8 Submenu » Data Entry «
In this submenu it is possible to
enable or disable the data entry
prompt during the measuring
process. In the basic setting,
the data input is activated.
1. Enable or disable
checkbox input of user/
subject data.
2. Accept the entry
Confirm. The return to the
menu is automatic.
6.2.9 Submenu » Set Date and Time «
In this submenu, you can set
the date and time.
1. Set the time and date
consecutively.
2. Accept the entry
Confirm. The return to the
menu is automatic.
Small discrepancies of the
internal clock can also be
compensated:
With + the current time is advanced by one minute.

With - the current time is retarded by one minute.

24
Settings
Location Database
LUEBECK
Location 1
are
BERLIN
Location 2
HAMBURG
Location 3
Location 4
Confirm
Menu
Settings
Change Current Location
Please select current location:
Location (default)
LUEBECK
BERLIN
HAMBURG
Revalstrasse
KLINIK
Confirm
Menu
with
Settings
Service Settings
input of user/subject data
the
Confirm Save
Menu
with
Settings
Set Date and Time
Set Time 14:31:27
Set Date
17.10.2013
with
Time Offset 0 h 1 min
Confirm Save
Menu
NOTICE
i i
X
The current time can be changed by +/- 1 minute within
24 hours.
6.3 Menu » Maintenance «
In this menu you can choose settings that allow a more
Close
accurate analysis of the measurement results. Some of the
settings made in this menu will be set to default once the
01723875_en.eps
instrument is switched off. The use of this menu is permitted for
trained service engineers.
6.3.1 Submenu » Subject Test Settings «
In this submenu you can set the measuring unit in which the
breath alcohol concentration will be displayed during normal
mode (active after power-on) and control mode.
The following units are available:
µg/l

X
mg/l

µg/100 ml

g/l

‰

%

Close
g/210 l

01823875_en.eps
When giving this data a conversion factor of 2100 between
breath and blood alcohol concentration is used.
The setting of the unit remains the same even after the
instrument is switched off.
6.3.2 Submenu » Control Mode «
X
In this submenu the control mode can be enabled and a test
gas type selected for measurements.
This setting is useful for work in the laboratory. In control mode,
the resolution of the measurement result is shown one decimal
point higher.
Close
By enabling the Lab report it is also possible to output sensor
raw data for a measurement.
01923875_en.eps
NOTICE
i i
Both settings will be deactivated after the instrument is
switched off.
X
+ -
Close
02033037_en.ep
Dräger Alcotest 9510 Standard IR / EC