Water Tank Machine Or Machine In Use With Water Tank; Machine In Use With Direct Water Connection - ECM Manufacture MECHANIKA MAX Bedienungsanleitung

Now you can start up your machine:

5.1. Water tank machine or machine in use with water tank

1 Open the cup warmer tray. Take out the water tank and rinse it thoroughly.
2 Fill the water tank with fresh water consisting of minimal amounts of lime, place it back into the water
tank guides and close the cup warmer tray.
3 Plug the machine into an electrical outlet. Turn the power switch to "1". The machine is now on.
4 The green signal lamp lights up.
5 The pump will fill the boiler of the machine with fresh water.
6 A large amount of water is required to fill the boiler for the first time, so the water tank will have to be
refilled with fresh water.
7 As soon as the boiler is filled, the pump will stop; the orange signal lamp is now on. As soon as the fresh
water falls to a certain level in the water tank, the machine switches off and the orange signal lamp turns
off. Refill with fresh water and the machine will restart and heat up automatically.
8 Move the group lever into the upper position and dispense approx. 500 ml of water. This way, the heat
exchanger will be filled with water and the circulation of the water in the thermosyphon system begins.
9 Move the group lever into the lower position. Refill the water tank.
10 Wait until the boiler pressure gauge indicates approx. 1.0-1.25 bar or 124° C (248°F) has been reached
(With default settings).
11 A manual "boiler ventilation" is not necessary because the MECHANIKA MAX is equipped with a
professional depression valve that ventilates the boiler during the heating-up phase.
12 The machine is now ready for use. Put the cups on the cup heater tray in order to preheat them.
If the first filling does not work, connect the machine to the water supply (see the following
chapter). After the first filling, you can switch the machine back to water tank and continue to
operate the machine with it.
Before preparing the first coffee, please rinse the machine by extracting about 2-3 water
tank fillings from the brew group and the hot water wand. When the machine is switched
off, more hot water can be dispensed. See also chapter 9.4.
The MECHANIKA MAX has a safety backup that prevents the machine from overfilling.
It is possible that the machine does not heat up during initial start-up or when a large amount
of water has been flushed via the hot water valve. In this case, please switch the machine off
briefly using the on/off switch and then switch it on again.
Please note that the filter holder, drip tray, cup tray and water tank are not suitable for the
dishwasher.

5.2. Machine in use with direct water connection

1 Plug the machine into an electrical outlet. Turn the power switch to "1". The machine is now on.
2 The green signal lamp lights up. The pump begins to fill the boiler of the machine with fresh water.
3 As soon as boiler has filled, no more pump noise will be heard; the orange signal lamp is on now and the
machine will heat up automatically
4 Move the group lever into the upper position and dispense approx. 500 ml of water. This way, the heat
exchanger will be filled with water and the circulation of the water in the thermosyphon system begins.
5 Move the group lever into the lower position.
6 Wait until the boiler pressure gauge indicates approx. 1.0-1.25 bar or 124° C (248°F) has been reached
(With default settings).
7 A manual "boiler ventilation" is not necessary because the MECHANIKA MAX is equipped with a
professional depression valve that ventilates the boiler during the heating-up phase.
8 The machine is now ready for use. Put the cups on the cup heater tray in order to preheat them.
Before preparing the first coffee, please rinse the machine by extracting about 5-8 l from
the brew group and the hot water wand. When the machine is switched off, more hot water
can be dispensed. See also chapter 9.4.
The MECHANIKA MAX has a fuse to prevent the machine from overfilling.
If the machine does not heat up when using it for the first time or when dispensing large
quantities of water through the hot water valve, please switch the machine off and on again.
Translation of the original German user manual
ENGLISH
38