Window Meanings - Agilent Technologies Varian TV 1001SEM Bedienungshandbuch

Window Meanings

N. Read/ Data
Write Type
000 R/W L
008 R/W L
100 R/W L
101 R/W N
102 R/W N
103 R/W N
104 R/W L
105 R/W N
106 R/W L
107 R/W L
108 R/W N
109 W L
110 R/W L
Description Admitted
Values
Start/Stop Start = 1
(in remote Stop = 0
mode the
window is a
read only)
Remote Remote = 1
(default) or Serial = 0
Serial con-
(default = 1)
figuration
Soft Start YES = 1
(write only in NO = 0
Stop condi-
tion)
Set Point 0 = Frequency
type 1 = Current
2 = Time
(default = 0)
Set Point (default = 643)
threshold
(expressed
in Hz, mA or
s)
Set Point 0 to 99999
delay: time
(default = 0)
between the
pump start
and the set
point check
(seconds)
Set Point sig- 0 = high level ac-
nal activation tive
type: the sig- 1 = low level ac-
nal can be tive
"high level
(default = 0)
active" or
"low level ac-
tive"
Set point 0 to 100
hysteresis
(default = 2)
(in % of
threshold)
Intercooling 0 = NO
1 = YES
Active Stop 0 = NO
(write only in 1 = YES
stop)
Baud rate 600 = 0
1200 = 1
2400 = 2
4800 = 3
9600 = 4
(default = 4)
Pump life/ To reset write '1'
cycle time/
cycle num-
ber reset
Interlock Impulse = 0
type Continuous = 1
(default = 1)
N. Read/
Write
111 R/W
120 R/W
121 R/W
122 R/W
123 Reserved to Varian service
124
125 R/W
126 R/W
130 Reserved to Varian service
200 R
201 R
202 R
203 R
204 R
205 R
206 R
210 R
(see
note 3)
79/87
TECHNICAL INFORMATION
Data Description Admitted
Type
L Analog out- 0 = frequency
put type: 1 = power
output volt-
(default = 0)
age signal
proportional
to frequency
or power
N Rotational 150 to 650
frequency
(default = 650)
setting (Hz)
N Maximum 150 to 650
rotational
(default = 650)
frequency in
Hz (active
only in Stop
condition)
L Set vent On = 1
valve on/off Off = 0
(on = closed)
(default = 1)
L Set the vent Automatic = 0
valve (see note 1.)
operation
On command = 1
(see note 2.)
N Vent valve 0 to 65535
opening
(corresponding to
delay
0 to 13107 sec)
(expressed
in 0.2 sec)
N Pump
current in
mA dc
N Pump volt-
age in Vdc
N Pump power
in W (pump
current x
pump voltage
duty cycle)
N Driving fre-
quency in
Hz
N Pump tem- 0 to 70
perature in
°C
N Pump status Stop = 0
Waiting intlk = 1
Starting = 2
Auto-tuning = 3
Braking = 4
Normal = 5
Fail = 6
N Error code Bit description:
see the following
figure
N Actual rota- 150 to 650
tion speed
in Hz
87-900-973-01(E)
Values