Inhaltsverzeichnis
Verwandte Anleitungen für Agilent Technologies SH-112
Inhaltszusammenfassung für Agilent Technologies SH-112
- Seite 1 Vacuum Products Division SH-112 INSTRUCTION MANUAL MANUALE DI ISTRUZIONI Dry Scroll NOTICE DE MODE D’EMPLOI Vacuum Pump BEDIENUNGSHANDBUCH 使用手册 使用説明書 사용 설명서 Manual No. 699904430 Revision B May 2012...
- Seite 2 SH-112 Dry Scroll Vacuum Pump Slo-Blo and Littelfuse are registered trademarks of Littelfuse, Inc. Copyright 2012 Agilent, Inc.
-
Seite 3: Declaration Of Conformity
Declaration of Conformity Declaration of Conformity Konformitätserklärung Déclaration de Conformité Declaración de Conformidad Verklaring de Overeenstemming Dichiarazione di Conformità 一致性声明 一致性声明 一致性声明 一致性声明 適合宣言 適合宣言 適合宣言 適合宣言 적합성 선언 Agilent, Inc. Vacuum Products Division Nous 121 Hartwell Avenue Nosotros Lexington, MA, 02421-3133 USA 我们... -
Seite 4: Warranty
SH-112 Dry Scroll Vacuum Pump Warranty Products manufactured by Seller are warranted against Warranty Replacement defects in materials and workmanship for twelve (12) and Adjustment months from date of shipment thereof to Customer, and Seller's liability under valid warranty claims is limited, at... -
Seite 5: Inhaltsverzeichnis
使用 ........12 SH-112 Typical Run Currents ... 20 保守... - Seite 6 SH-112 Dry Scroll Vacuum Pump This page intentionally left blank.
-
Seite 7: Instructions For Use
The SH-112 is a hermetic, dry scroll vacuum pump. This pump is suitable for pumping air or inert gases. The pump Total weight of the packing, SH-112 pump included, is is not intended to pump corrosive, explosive, or particu- approximately 20 kg (44 lbs). -
Seite 8: Installation
Death may result from contact with WARNING If placing the SH-112 pump inside an enclosure, provide high voltages. Always take extreme care ample room to supply ambient air to both the front and and observe the accident prevention rear air intakes of the pump. -
Seite 9: Istruzioni Per L'uso
La pompa viene fornita in un imballo protettivo speciale; trario alle normative nazionali specifiche. se si presentano segni di danni, che potrebbero essersi La pompa a secco Scroll SH-112 è una pompa ermetica verificati durante il trasporto, contattare l'ufficio vendite adatta a pompare aria or gas inerti. -
Seite 10: Installazione
SH-112 Dry Scroll Vacuum Pump Installazione Manutenzione Non installare e/o utilizzare la pompa in ambienti esposti Il personale addetto alla condotta ed alla manutenzione ad agenti atmosferici (pioggia, gelo, neve), polveri, gas della pompa deve essere ben addestrato e deve avere una aggressivi, in ambienti esplosivi o con elevato rischio di approfondita conoscenza delle norme antinfortunistiche. -
Seite 11: Instructions D'utilisation
La pompe SH-112, est une pompe à vide sèche et hermé- vant s'être produits pendant le transport, contacter auss- tique. Cette pompe convient pour le pompage de l'air ou itôt le bureau de vente local. -
Seite 12: Installation
SH-112 Dry Scroll Vacuum Pump Installation L'arrêt de la pompe ne requiert aucune manœuvre parti- culière; il faut seulement la déconnecter de l'alimentation Ne pas installer et/ou utiliser la pompe dans des milieux électrique grâce au bouton On/Off. exposés aux agents atmosphériques (pluie, gel, neige), à... -
Seite 13: Gebrauchsanleitung
Mißachtung der nationalen Bestimmungen übernimmt geliefert. Eventuelle Transportschäden sind der zuständi- Firma Agilent keinerlei Haftung. gen örtlichen Verkaufsstelle zu melden. Die Pumpe SH-112 ist eine hermetisch dichte trocken- Das Verpackungsgewicht beträgt, einschließlich der laufende Vakuumpumpe (Scrollpumpe). Pumpe SH-112, ungefähr 20 kg. -
Seite 14: Installation
SH-112 Dry Scroll Vacuum Pump Installation Das Ausschalten der Pumpe erfordert keine speziellen Schritte, sie braucht nur durch Betätigung des Schalters Die Pumpe darf nicht in Umgebungen installiert und/oder On/Off abgeschaltet werden. benutzt werden, die ungeschützt vor Witterungsbedin- ANMERKUNG Das Einlaßventil schließt unverzüglich gungen (Regen, Frost, Schnee), Staub und aggressiven nach Abschalten der Pumpe. -
Seite 15: 使用说明
SH-112 Dry Scroll Vacuum Pump 使用说明 使用说明 使用说明 使用说明 一般信息 一般信息 一般信息 一般信息 贮存 贮存 贮存 贮存 当将泵运输到其它地方或进行贮存时，不应超出以下环 本设备仅可由专业人员操作和使用。操作本设备之前，使 境范围要求： 用人员应认真阅读本使用手册及由 Agilent 提供的其它所 有相关说明。 Agilent 对于因未按使用手册指导进行违规 − − 温度: 20 °C 至 +60 °C ( 4 °F 至 140 °F) 操作、未经培训人员执行不当操作、未获授权的设备连... -
Seite 16: 维护与维修
SH-112 Dry Scroll Vacuum Pump 安装 安装 维护与维修 维护与维修 安装 安装 维护与维修 维护与维修 不要将泵安装在易受自然天气侵害 (如下雨、下雪、结冰) 负责操作和维护泵的人员，必须接受良好的专业培训，并 的环境中，不要在多尘、周围存在腐蚀性气体、易发生爆 熟知突发事件预防及处理规程。 炸场所或易引起火灾的环境中使用本泵。 警告 警告 警告 警告 接触高电压将有导致死亡的危险。 操作期间，必须留意并符合以下环境条件。 应始终保持格外小心，并遵守预防突发 事件的规章和要求。 温度: +5 °C 至 +40 °C (41 °F 至 104 °F) 机器处于开机运转状态时，应特别留 相对湿度: 0 至... -
Seite 17: はじめに
SH-112 Dry Scroll Vacuum Pump はじめに はじめに はじめに はじめに 一般情報 一般情報 一般情報 一般情報 保管 保管 保管 保管 ポンプを輸送および保管する際は、以下の環境条件を 本装置は、 専門家による使用を想定して設計されていま 守ってください。 す。 ユーザーは装置を使用する前に、本取扱説明書、お よび Agilent Technologies が提供するその他の情報を読 − − 20 °C ~ +60 °C ( 4 °F ~ 140 °F) 温度:... - Seite 18 SH-112 Dry Scroll Vacuum Pump 設置 設置 設置 設置 保守 保守 保守 保守 大気中の作用物 (雨、雪、氷)、ダスト、悪性ガスにさら ポンプの操作•保守責任者は、十分な訓練を受けており されるような環境、爆発性雰囲気、または火災危険度の 事故防止規則に精通している必要があります。 高い環境下でポンプを設置したり、 使用したりしないで 警告 警告 警告 警告 高電圧に触れると死亡する恐れがあ ください。 ります。 常に十分な注意を払い、事故 動作時は以下の環境条件に準拠してください： 防止規則を守ってください。 +5 °C ~ +40 °C (41 °F ~ 104 °F) 温度:...
-
Seite 19: 사용 지침 사용 지침
는 공기 또는 불활성 가스의 펌핑 작업에 적합합니다. 판매 사무소로 연락하십시오. 이 펌프는 유독성, 부식성, 폭발성 또는 미립자-성형 가스 SH-112 펌프를 포함한 포장품의 총 중량은 약 20 kg 의 펌핑 작업용으로 고안되지 않았습니다. (44 lbs)입니다. 다음 내용들은 본 장비 사용시에 작업자의 안전을 보장... -
Seite 20: 유지 보수
SH-112 Dry Scroll Vacuum Pump 설치 설치 설치 설치 유지 유지 보수 유지 유지 보수 보수 보수 비, 눈, 얼음, 먼지 또는 활성 가스에 노출되거나, 폭발 또 펌프 작동 및 유지 보수 책임자는 충분한 교육을 받아야 는 화재 발생 우려가 있는 환경에서는 이 펌프를 설치하... -
Seite 21: Technical Information
SH-112 Dry Scroll Vacuum Pump Technical Information Table 1 Specifications Model SH-112 Dry Scroll Single Hermetic Vacuum Pump Interface dimensions See Figure 1 on page 16 Peak pumping speed 50 Hz: 90 L/m, 5.4 m /hr (3.3 cfm) 60 Hz: 110 L/m, 6.6 m /hr (4.0 cfm) -
Seite 22: Interface Drawing With Dimensions
SH-112 Dry Scroll Vacuum Pump Figure 1 Interface Drawing with Dimensions * This graph represents optimal conditions. The SH-112 demon- strate a higher base pres- sure in applications that include continuous vent- ing cycles. Figure 2 Pumping Speed Curves... -
Seite 23: Unpacking And Inspection
Unpacking and Inspection 1. Orient the shipping container with “This End Up” on top. 2. Open the box and carefully lift the SH-112 out of the box. 3. Save the carton and all packing materials. 4. Inspect the pump for damage. If there is shipping damage, contact the freight carrier and your local Agilent sales office immediately. -
Seite 24: Installation
SH-112 Dry Scroll Vacuum Pump Installation Do not block the fan ducts. Blocking CAUTION these ducts can cause pump overheat- Safety ing. A pump surface temperature in excess of 65 ° C (150 ° F) is potentially Do not remove or modify any safety or insulating equip- damaging. -
Seite 25: Sh-112 Power Cord Selection
10 A capacity. be used with a grounding plug that looks like the plug illustrated in Figure 4. Table 2 SH-112 Power Cord Selection If repair or replacement of the cord or plug is necessary, connect Country... -
Seite 26: Run Currents
126 V 180 V 200 V 230 V 252 V 60 Hz 50 Hz Start Current Table 4 lists the typical SH-112 maximum starting current and duration. Table 4 Typical SH-112 Maximum Starting Current and Duration @ 115 V 50 Hz... -
Seite 27: Mechanical Connections
Operation Isolation Valve Cleaning the Pump The SH-112 has an integral automatic isolation valve. An Unlike conventional oil-sealed pumps, Agilent dry scroll internal timer opens the valve 10 seconds after the pump pumps do not contain fluid for the cleansing of accumu- is switched ON. -
Seite 28: Troubleshooting
Identify the cause of the overload. The SH-112 is equipped with an auto-reset thermal motor protector. This protector will automatically shut down the pump when it detects an overload condition, and will automatically restart the pump when the motor has cooled to... -
Seite 29: Maintenance
14 mm crescent wrench able to minimize downtime. Razor blade or side-cutting pliers The parts needed for tip seal replacement on the SH-112 Compressed air (optional) are available in the kit described in Table 6. This kit con- If dangerous gases were being pumped,... -
Seite 30: Exploded View Of Pump Body
SH-112 Dry Scroll Vacuum Pump 4. Cut the Tip Seal about 1/8" (3 mm) from the outer 9. If a 1/8" NPT solid plug was removed from the gas groove end. ballast port during disassembly, reinstall it. Apply Loctite pipe thread sealant PTS 567 sparingly to the 5. - Seite 31 Please follow these instructions whenever one of our products needs to be returned. 1) Complete the attached Request for Return form and send it to Agilent Technologies (see below), taking particular care to identify all products that have pumped or been exposed to any toxic or hazardous materials.
- Seite 32 This page intentionally left blank. 4) HEALTH and SAFETY CERTIFICATION AGILENT TECHNOLOGIES CANNOT ACCEPT ANY PRODUCTS CONTAMINATED WITH BIOLOGICAL OR EXPLOSIVE HAZARDS, RADIOACTIVE MATERIAL, OR MERCURY AT ITS FACILITY. Call Agilent Technologies to discuss alternatives if this requirement presents a problem.
- Seite 33 Shipping Regulations (IATA, DOT, etc.) and carrier requirements. Customers receiving an Advance Exchange product agree to return the defective, rebuildable part to Agilent Technologies within 15 business days. Failure to do so, or returning a non-rebuildable part (crashed), will result in an invoice for the non-returned/non-rebuildable part.
- Seite 34 SH-112 Dry Scroll Vacuum Pump This page intentionally left blank.
-
Seite 36: Agilent Technologies
Agilent Technologies Vacuum Product Division United States & Canada India Southeast Asia Agilent Technologies Agilent Technologies Agilent Technologies Vacuum Products Division Vacuum Product Division Vacuum Products Division 121 Hartwell Avenue 205-A, “A” wing of Galleria, South East Asia (SEA) - Alex Ho...