Cleaning; Transport; Storage - Scheppach SG3200 Serie Original Bedienungsanleitung

4. Return the choke lever (3) to the OPEN position
while the engine warms up.
WARNING:Ensure that you do not injure your fingers.
If the motor does not start and a piston was not raised
completely, the starter grip may suddenly spring back
to the engine. Avoid the starter grip springing back
against the engine. Feed it back slowly by hand to
ensure that the cover is not damaged.
Shutting the engine off
1. Switch the generator off
2. Set the engine switch to off
3. Turn the fuel valve to off
In an emergency, set the engine switch to off!
Electrical devices that can be connected
This power unit can power light bulbs, heaters, drills,
water pumps, etc. Do not exceed the load limit speci-
fied for the power unit.
The power unit may not be used to power devices that
have a high power requirement.
The power unit cannot be used for precision devices
such as computers. These precision devices may be
damaged under certain circumstances by distortions
caused by the broad wave when the power unit's pow-
er is output. Do not connect the power unit to the elec-
trical installation of a building.
WARNING:Connection to the electrical installation of a
building may result in the electric current being returned
to the mains supply wires. This return causes a risk of
a fatal electric shock for employees of the electricity
supplier or other persons who touch the wires during
a power failure.
Connection to the electrical installation of a building
can also cause the electric current of the electricity
supplier to return to the power unit. When the mains
supply is restored, the power unit may explode, burn
or cause a fire to break out in the electrical installation
of the building.
Disconnector (13)
The circuit breaker automatically disconnects the
power unit in the event of a short circuit or significant
overload of the generator at the socket. If the fuse has
automatically popped out to the off position, check that
the connected electrical appliance is in good working
order and does not exceed the circuit's permissible
load limit before pushing the fuse back in.

10. Cleaning

Attention!
Always shut the engine down and remove the spark
plug connector before carrying out any cleaning work.
We recommend that you clean the device directly after
every use.
Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic parts
of the device. Make sure that no water can penetrate
the device interior.

11. Transport

Transport
1. Allow the engine to cool before transporting.
2. Before transporting the power unit, switch the en-
gine switch (9) to the OFF position and turn the
fuel valve (4) to the OFF position
3. Keep the power unit level so that no petrol is
spilled. Petrol vapour or spilled petrol may ignite.
4. Ensure that the power unit does not fall and do not
subject it to any blows during transport.
5. For short transport, transport the generator us-
ing the transport wheels (15) and the transport
handle (8).

12. Storage

Store the device and its accessories in a dark, dry and
frost-free place that is inaccessible to children. The op-
timum storage temperature lies between 5 and 30 ˚C.
Store the power tool in its original packaging. Cover the
power tool to protect it from dust or moisture. Store the
operating manual with the power tool.
When storing for a long period of time
1. Empty the fuel tank and run the carburettor empty.
2. Unscrew the spark plug.
3. Approx. Pour approximately 20 ml of clean engine
oil through the spark plug hole into the cylinder.
4. Pull the starter rope out slowly so that the oil dis-
tributes itself in the engine and screw the spark
plug back in.
5. Remove all dirt, deposits and dust from the engine
and the cylinder head ridges.
6. Clean the air filter or replace it if it is very dirty.
7. Store the power generator securely in a dry place
that is inaccessible to children.
www.scheppach.com GB | 25