Carrier WTC-LEX-WD Bedienungsanleitung Seite 7

manufacturer.
The output wires must remain between 17 AWG (1 mm²)
and 16 AWG (1.5 mm²). Make sure the cable performances
suit the connected loads.
Wiring ON/OFF lighting outputs
Table 9-1: Expansion Module Outputs
ON/OFF lighting relay outputs can provide
Expansion Outputs Type
up to 240 VAC (-WD and -ST models), same
Module
voltage as power supply – 2 A max per
output, 6 A maximum in aggregate for each
ECx-Light-4 O /O
n ff
module. As an illustration, this corresponds
ECx-Light-4D O /O
n ff
1-10 V Dimming Lighting
to 8 electronic ballasts or 4 electromagnetic
ECx-Light-4DALI DALI
ballasts per output (230 VAC).
ECx-Blind-4 High Voltage Shade / Sunblind
The starting current must be kept under 80 A
ECx-Blind-4LV 24 VDC Shade / Sunblind
during 20 ms.
Wiring ON/OFF Lighting Outputs
ON/OFF lighting relay outputs can provide up to 240 VAC (-WD and
-ST models) or 277 VAC (-STP models) (same voltage as power
supply - 2 A max per output, 6 A maximum in aggregate for each
module). As an illustration, this corresponds to 8 electronic ballasts or
4 electromagnetic ballasts per output @ 230 VAC.
The starting current must be kept under 80 A during 20 ms.
Figure 9: ON/OFF lighting output wiring
L
Wiring 1-10 V dimming lighting Outputs
N
Each dimmer relay output can provide up to
240 VAC (-WD and -ST models), same
voltage as power supply - 2 A max per
Figure 9-1: ON/OFF Lighting Output Wiring
output, 6 A maximum in aggregate for each
Wiring 1-10 V Dimming Lighting Outputs
module, and 1-10 V commands (sourcing
Each dimmer relay output can provide up to 240 VAC (-WD and -ST
current / sinking current: +/- 5 mA for each
models) or 277 VAC (-STP models) (same voltage as power supply - 2
output).
A max per output, 6 A maximum in aggregate for each module) and
1-10 V commands (sourcing current / sinking current: +/- 5 mA for each
The starting current must be kept under 80 A
output).
The starting current must be kept under 80 A during 20 ms.
during 20 ms.
AOx
COM
L
N
Figure 10: Dimmer lighting output wiring
Figure 9-2: Dimmer Lighting Output Wiring
ECx-Light/Blind Series
Number of
outputs
Lighting
Lighting or
Lighting group X – light 1
Lighting group X – light 2
Lighting group X - light 1
Lighting group X - light 2
+
-
L
N
Lighting group X
– ballast 1
+
-
L
N
Lighting group X
– ballast 2
ECx-Light-4DALI-WD marking
L
N
Wiring 24 VDC Shade / Sunblind Outputs
DA+
DA-
Each 24 VDC shade / sunblind output can
provide 24 VDC (2 A maximum in aggregate
for each module) to drive 24 VDC motors.
4
4
DA+
4
DA-
L
4
N
4
Figure 11: High voltage shade / sunblind output
wiring
Figure 9-3: DALI Output Wiring
Wiring High Voltage Shade / Sunblind Outputs
Each high voltage shade / sunblind output can provide up to 240
(same voltage as power supply - 2 A max per output, 8 A maximu
aggregate for each module) to drive one shade / sunblind motor
output. Only one motor can be driven by each output.
Parallel wiring of shade / sunblind AC motor is st
forbidden, damage to the motors and/or the installation
occur.
Figure 9-4: High Voltage Shade / Sunblind Output Wiring
Wiring 24 VDC Shade / Sunblind Outputs
Each 24 VDC shade / sunblind output can provide 24 VDC
maximum in aggregate for each module) to drive 24 VDC motors.
Figure 9-5: 24 VDC Shade / Sunblind Output Wiring
External connector marki
L
G
N
D2
D1
DA
DA
L
N
bus DALI X - ballast 1
▲ Up
▼ Down
DA
DA
L
N
bus DALI X - ballast 2
N
Neutral
1
2
High Voltage Sunblind
Mx+
Mx-
24 VDC Sunblind
Earth
Up
Down
Up
Down
4
7