Specifications - Stihl HSA 56 Gebrauchsanleitung

18 Specifications

17.2 Troubleshooting the Charger
Fault LED on Char‐
ger
Battery not being The LED fla‐
charged. shes red.
18 Specifications
18.1 STIHL HSA 56 Hedge Trimmer
– Approved battery: STIHL AK
– Weight without battery: 2.9 kg
For battery life see www.stihl.com/battery-life.
18.2 Cutting Blades
– Tooth spacing: 30 mm
– Cutting length: 450 mm
– Sharpening angle: 35°
18.3 STIHL AK Battery
– Battery technology: Lithium-ion
– Voltage: 36 V
– Capacity in Ah: see rating label
– Energy content in Wh: see rating label
– Weight in kg: see rating label
– Permissible temperature range for operation
and storage: -10°C to +50°C
18.4 Charger STIHL AL 101
– Rated voltage: see rating plate
– Frequency: see rating plate
– Rated power: see rating plate
– Charging current: see rating plate
– Permissible temperature range for use and
storage: + 5 °C to + 40 °C
The charging times are indicated at
www.stihl.com/charging-times.
18.5 Extension Cords
If an extension cord is used, the cross sectional
area of its conductors must meet the following
minimum requirements – depending on the line
voltage and length of the extension cord:
If rated voltage on the rating label is 220V to
240V:
– Cord length up to 20 m: AWG 15 / 1.5 mm²
– Cord length 20 m up to 50 m: AWG 13 /
2.5 mm²
If rated voltage on the rating label is 100V to
127V:
– Cord length up to 10 m: AWG 14 / 2.0 mm²
0458-714-9821-D
Cause
No electrical contact
between charger and
battery.
There is a malfunction
in the charger.
– Cord length 10 m up to 30 m: AWG 12 /
3.5 mm²
18.6
The K-value for sound pressure levels is 2 dB(A).
K-value for sound power levels is 2 dB(A). K-
value for vibration level is 2 m/s².
STIHL recommends wearing ear defenders.
– Sound pressure level L
to EN 60745-2-15: 80 dB(A).
– Sound power level L
EN 60745-2-15: 91 dB(A).
– Vibration level a
EN 60745-2-15
– Control handle: 2.7 m/s². The K value for
– Loop handle: 1.2 m/s².
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual vibration stress has to be esti‐
mated. The times when the electric power tool is
switched off and the times when it is switched on
but running under no load can be taken into
account in the estimate.
For information on compliance with Employers'
Vibration Directive 2002/44/EC see
www.stihl.com/vib.
18.7
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
Remedy
► Remove the battery.
► Clean contacts on charger.
► Insert battery.
► Do not use the charger and contact your
STIHL dealer for assistance.
Sound Values and Vibration
Values
p
measured according to
wA
measured as specified in
hv
the vibration level is 2 m/s².
REACH
English
measured according
39