Package Contents; Description (Fig. A); Electrical Safety; Using An Extension Cable - DeWalt D27400 Anweisungen

E N G L I S H
- Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.

Package contents

The package contains:
1 Table top
1 Motor frame
1 Motor unit with switch box
1 Saw blade guard
1 Dust spout
1 Fence
1 Push stick
1 Skinpack containing:
1 Upper blade guard
1 Fence clamping support
1 Fence bracket
1 Fence support
1 Motor frame cover
1 Switch box bracket
1 Elevating shaft
1 Moveable saw blade guard
1 Bevel scale
2 Columns
1 Pivot pin
1 Elevating handle
1 Fence lock knob
2 Bevel lock knobs
3 Cable clamps
2 Hinges
2 M8 x 16 hex head bolts
2 M8 x 30 hex head bolts
2 M6 x 20 coach bolts
3 M6 self-locking nuts
2 M8 self-locking nuts
5 M6 nuts
2 M6 wing nuts
5 M6 x 16 Allen screws
1 M6 x 25 Allen screw
2 M5 x 60 slotted head screws (D27400T)
2 M5 nuts (D27400T)
4 4.2 x 16 crosshead screws (D27400)
2 4.8 x 16 crosshead screws
7 3.5 x 9.5 crosshead screws
2 M4 x 8 crosshead screws
2 D5 flat washers (D27400T)
1 D6 flat washer
2 D6-11 flat washers
6 D6.6-18 flat washers
2 D9-27 flat washers
3 D6.4 toothed washers
2 D8 circlips
2 D12 circlips
1 Skinpack containing:
1 Table insert
1 Riving knife clamping set
1 Riving knife
1 Saw blade
1 Blade clamp washer set
1 Spacer
1 Key
1 Blade nut
1 4.8 x 16 crosshead screw, countersunk
1 M10 x 30 coach bolt
1 M10 nut
1 D10 Belleville washer
22
1 Allen key 5 mm
1 Allen key 8 mm
1 Box spanner 10 mm
1 Box spanner 13 mm
1 Combination wrench
1 Box containing:
4 Legs
2 Short cross bars
2 Long cross bars
2 Motor frame brackets
1 Fence clamping rail
1 Fence driving rail
1 Bag containing:
2 Fence rail clamp knobs
5 M6 x 20 coach bolts
16 M6 x 12 hex head bolts
3 M6 self-locking nuts
8 M6 cap nuts
16 M6 nuts
16 D6 flat washers
8 D6 Belleville washers
5 D6 compression springs
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.

Description (fig. A)

Your D27400/D27400T site saw is a professional machine designed for
sawing wood and wood products at construction sites.
1 On/off switch
2 Table top
3 Table insert
4 Fence driving rail
5 Upper blade guard
6 Riving knife
7 Saw blade
8 Combined rip and mitre fence
9 Legstand
10 Floor anchor hole
11 Elevating handle
12 Fence clamping rail

Electrical safety

The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.

Using an extension cable

If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
conductor size is 1.5 mm2.
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Conductor size (mm2) Cable rating (Amperes)
1.50 15
2.50 20
4.00 25
Cable length (m)
7.515 25 30 45 60