Connecting Electrical Devices And Generator Load-Capacity - HERON 8896430 Bedienungsanleitung

•
ATTENTION
y Do not release the handle of the pull starter, rather
allow it to return to the initial position while holding
it since releasing the handle suddenly from the pul-
led out position would result in a rapid return and
this could cause damage to the starting mechanism.
7. After starting the generator, gently push the
choke rod back in
y In the event that while pushing in the choke pull rod,
the engine is throttled, immediately quickly pull the
choke pull rod out and wait a few moments and then
attempt to push it in again. In the event that the choke
pull rod is not pushed in while the generator is running,
then after some time the engine will be throttled or the
engine will not achieve full power output. When run-
ning the generator, it is necessary to push the choke pull
rod in within a certain time of starting the engine.
y To start a generator with a warm engine that has been
running for an extended period of time, it may not be
necessary for the choke pull rod to be in the pulled out
position. It may, however, be necessary to check this by
performing a practical test in the event that the genera-
tor cannot be started with the choke pull rod set in the
generator operating position.
8. Connect the electrical devices as described in
chapter VI, before activating the circuit brea-
kers levers to the "ON" position.
•
ATTENTION
y In the event that there is an unusual noise, vibrations or
operation while the generator is running, immediately
turn off the generator and identify and rectify the cause
of this unusual operation. If the unusual operation is
caused by a fault inside the device, have it repaired at
an authorised service centre for the HERON® brand
through the vendor or directly at an authorised service
centre (service locations are listed at the HERON® gene-
rators website address at the start of this manual).
VI. Connecting
electrical devices and
generator load-capacity
y It is possible to connect electrical devices intended for
standard mains power into the 230 V~50 Hz power sockets.
y It is possible to connect three-phase electrical devices
intended for 398V alternating-current voltage to be con-
nected to the 400 V~50 Hz power socket.
y The blue 32 A/230 V or red 400 V three-phase power
plugs may only be installed on power cords of
electrical devices by an electrician with the necessa-
ry qualifications!
111
.
y To power 230 V electrical devices connected to the
16 A or 32 A socket, set the toggle switch (Fig. 1,
position 9) to position 230 V. To power 400 V electri-
cal devices, set the toggle switch to position 400 V.
•
WARNING
y The generator must not be transported or moved
to a different location while it is running. Turn it off
before moving it.
y For powering electrical devices it is necessary to
respect the following conditions, otherwise the
powered electrical devices or the generator may
be damaged:
y The total nominal (operating) power input of all
the connected electrical devices must not exceed
the nominal (operation) electrical power output
of the generator. To determine the nominal power
input of an electrical device, it is possible to use
an affordable socket power input meter (a watt-
meter). The total power output of the generator is
understood to mean the total drawn power input
of all the electrical devices connected to the gene-
rator for a certain power voltage, i.e. total power
input of all the electrical devices powered from the
230 V 16 A/32 A power sockets or the 400 V socket.
y Turn on (start / put into operation) electrical
devices gradually one after the other with
a time interval in between and not all devices
at the same time. The large surge power input
caused by all the connected electrical devices
being turned on may cause a voltage spike and
damage the connected electrical devices.
y To be safe, it is better to connect sensitive
electrical devices such as computers, TVs, offi-
ce equipment, etc. via overvoltage protection.
Extension cords with sockets having overvol-
tage protection can be purchased in stores.
y The generator must not be concurrently used for
powering sensitive electrical devices (e.g. computer,
TV, office equipment) and an electrical device with
a power electric motor, which has an impulse ramp-
-up (starting) power input and fluctuating power
input based on the load placed on the electric
motor such as for example hand power tools, com-
pressors, high-pressure washers, etc. since this may
result in "peak" voltage spikes (fluctuations), which
may damage sensitive electrical devices.
y In the event that the generator is used as a bac-
kup electrical energy source for powering TN-C-S
(TN-C) networks (i.e. fixed electrical grids in
apartments, houses, etc.), the connection of the
generator must be performed only by an electri-
cian with the necessary qualifications, since it
must be put into balance with the IT network of
the generator with the TN-C-S (TN-C) grid.
EN