Headphone Output 3; Display 5; Aptx Bluetooth Connection Q; Audio Controls - Rotel A11 Bedienungsanleitung

NOTE: Be sure there are no loose wire strands that could touch adjacent
wires or connectors.

Headphone Output 3

The headphone output allows you to connect headphones for private listening.
This output accepts a standard 3.5mm (1/8") mini stereo headphone
connector. Plugging in a set of headphones does not cut off the signal to the
4
speakers. Use the front panel
buttons to turn off the speakers.
NOTE: Because the sensitivity of speakers and headphones can
vary widely, always reduce the volume level before connecting or
disconnecting headphones.

Display 5

The front panel display shows the source selected, volume level and tone
settings. The display provides access to the setup and configuration menu
options of the amplifier.

APTX Bluetooth Connection q

q
The Bluetooth Antenna on the unit's back panel is for wireless streaming
via Bluetooth, from your device (i.e. mobile phones, tablets or computers).
From your device, look for "Rotel Bluetooth" and connect to it. Connection
is normally automatic, but if prompted for a password, please enter "0000"
on your device. The unit supports both traditional Bluetooth and APTX
Bluetooth audio streaming.

Audio Controls

Volume Control 6 E

Turn the control clockwise to increase the volume, or counter clockwise to
decrease the volume. From the remote control press the volume + or - button
to turn the volume up or down. Press the MUTE
mute the volume.

Balance Control 8 B

The Balance Control adjusts the left-to-right balance of the sound output. The
factory default is the center position or "0". To change the balance from
the front panel, press the MENU
BALANCE SETTING mode. Then press the - or + buttons on the front panel to
change the value to LEFT or RIGHT. The value can change from L15 to R15.
NOTE: This setting is saved permanently including after powering off
the A11.
To make temporary changes not saved after power off, from the remote,
press the BAL button to access the BALANCE SETTING menu, then press
B
the up/down/left/right arrow buttons to adjust.
C

Source Input Selector 7 I

Press the corresponding input button on the front panel
to select the desired listening source.
I
J
or remote control A-B speaker selector
F button to completely
8
button to toggle the front display to
7 or remote control

Tone Control

The A11 features 4 different Tone Control options to provide a wide array
of listening options. The options include a BYPASS mode that disables the
Bass and Treble controls for the most direct audio path, ENABLED mode
that allows user selectable Bass and Treble settings and ROTEL BOOST
and ROTEL MAX modes supporting optimized configurations for multiple
listening environments and styles.
The factory default option is set to BYPASS to provide the purest possible
sound. The tone settings can be changed using the IR remote control or
the front panel.
To temporarily change the Tone Control push the BYPASS
remote control to cycle through the 4 different modes. When Tone Enabled
is selected the Bass and Treble settings can be changed using the remote
control by pressing the BASS or TREB
down/left/right arrow buttons on the remote to adjust the value. The
C
BYPASS, ROTEL BOOST and ROTEL MAX settings do not allow changes to
the Bass and Treble settings.
NOTE: These settings are temporary and are not saved after the A11
is powered off or in standby mode.
The Tone Control setting can be saved permanently (even after power off)
using the front panel setup menu. A description of the Tone Modes and
setup process is listed below.

Tone Bypass

Bass and Treble Controls are not active to ensure the purest possible sound.
To select this option press the front panel
repeatedly to toggle to the Tone Setup menu. Then press the - or + buttons
to select the BYPASS mode. This mode is the factory default option.

Tone Enabled

When the Tone Enabled option is selected the Bass and Treble levels can
be changed using the BASS B
and pressing the up/down/left/right
To select this option press the front panel
repeatedly to toggle to the Tone Setup menu then press the - or + buttons
to select the ENABLED mode.
NOTE: Be particularly careful when turning the tone controls up. This
increases the power output in the bass or treble range increasing the
load on the amplifier and speakers.

Tone Rotel Boost

The Rotel Boost mode is unique to Rotel and delivers a customized listening
experience. The audio performance is "boosted" and delivers a unique
blend of tonal characteristics. To select this option press the front panel
or IR remote MENU K button repeatedly to toggle to the Tone Setup menu
then press the - or + buttons to select the ROTEL BOOST mode.

Tone Rotel Max

Rotel Max increases the low frequency output to deliver more bass. This
feature is ideal for music, listening environments or speakers that benefit
from more bass while still maintaining the tones of the vocal and midrange
frequencies. To select this option press the front panel
MENU button repeatedly to toggle to the to the Tone Setup menu then
K
press the - or + buttons to select the ROTEL MAX mode.
B button on the
B buttons then pressing the up/
8
or IR remote MENU
or TREB B buttons on the IR remote control
C arrow buttons to adjust the value.
8
or IR remote MENU
8
or IR remote
11
K button
K button
8