Quick Start Atys P M - socomec ATyS p M Installationshandbuch Und Bedienungsanleitung

3. QUICK START ATYS p M
542934F
ATyS p M
40 - 160 A (4P)
AUTOMATIC TRANSFER
SWITCHING EQUIPMENT
Preliminary operations
Check the following upon delivery and after
removal of the packaging:
• Packaging and contents are in good condition.
• The product reference corresponds to the order.
• Contents should include:
Qty 1 x ATyS M
Qty 1 x Emergency handle extension rod
Qty 1 x Set of terminals
Quick Start Guide
Warning
Risk of electrocution, burns or injury to
persons and / or damage to equipment.
This Quick Start is intended for personnel
trained in the installation and commissioning
of this product. For further details refer to the
product instruction manual available on the
SOCOMEC website.
• This product must always be installed and
commissioned by qualified and approved
personnel.
• Maintenance and servicing operations should
be performed by trained and authorized
340
personnel.
324
• Do not handle any control or power cables
connected to the product when voltage may
be, or may become present on the product,
directly through the mains or indirectly through
13 26
external circuits.
• Always use an appropriate voltage detection
device to confirm the absence of voltage.
• Ensure that no metal objects are allowed to fall
in the cabinet (risk of electrical arcing).
Failure to observe good engineering practices
as well as to follow these safety instructions may
expose the user and others to serious injury or
death.
Risk of damaging the device
In case the product is dropped or damaged
in any way it is recommended to replace the
complete product.
Installation standards must be respected.
Accessories
• Bridging bars 125A or 160A.
• Control voltage transformer (400Vac
• Voltage sensing and power supply tap.
• Terminal shrouds.
• Auxilliary contact blocks.
• Polycarbonate enclosure.
• Polycarbonate extension box.
• Power Connection Terminals.
• ATyS D10 remote display unit.
• ATyS D20 remote control and display unit.
CORPORATE HQ CONTACT:
SOCOMEC SAS,
1-4 RUE DE WESTHOUSE,
67235 BENFELD, FRANCE
www.socomec.com
To download, brochures,
2 clips de verrouillage
catalogues and technical manuals
8 DE
Installation and Commissioning
STEP 1
Cabinet / Back
Plate Installation
1 1
Installation
Caution: Ensure that the product is installed on a flat rigid surface.
116
18
MAX : 2
46
53
73,5
52
230Vac).
6 mounting brackets - 6x M6 screw - 2,5 Nm
Tighten to avoid movement on the DIN rail.
DIN Rail
IEC 60715
STEP 2 STEP 3
CONTROL / AUX
Connecting the
POWER terminal
power section
connections
340
324
116
13 26
OK
OK OK
340
326
104 176
OK OK OK
OK OK OK OK
QUICK START GUIDE
STEP 4 STEP 5
Check Programming
Capacitor charging
Return to zero capacitor charge. While
the indicator is flashing, the return to 0
function is unavailable.
Operating mode
: 1 yellow LED for MANU mode active.
AUT: 1 green LED for AUTO mode active.
Fault LED
1 red LED to indicate the status of the
product. Open and close the AUT/MAN
cover to reset the fault.
Power Supply LED
1 green LED
- Always off: both power supplies off or
software error if other indicators are on.
- Always on: product power supply on.
Padlocking
configuration
The ATyS M is delivered
with padlocking configured to
Recommended
the O position.
orientation
Recommended
18
OK OK OK
OK
OK OK OK OK
OK
MAX : 2
OK OK OK OK
46
OK
53
73,5
OK OK OK
To allow padlocking in all
OK
positions (I - O - II), configure
the ATyS M as follows before
OK OK OK
installation. (Screw is located at
the back of the product).
OK
1
OK OK
Posidriv PZ2
2
3
Posidriv PZ1
2,2 lb-in/1 Nm
ATyS p M – 542935E – SOCOMEC
EN EN
STEP 6A
Automatic
Operation
STEP 6B
Emergency
Manual Operation
STEP 6C
Padlocking
OK OK OK
OK OK
OK
Posidriv PZ2
OK
2x 2x
2x
Posidriv PZ2
2,2 lb-in
0,25 Nm