With The Drag Guide (21) Not Fixed In Place - Parkside MPKZ 2000 A1 Bedienungs- Und Sicherheitshinweise

• Before making the cut, check that no collision can occur be-
tween the stop rails (16a) and the saw blade (6).
• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Use the handle (1) to push back the machine head (4) and
fix it in this position if required (dependent on the cutting
width).
• Place the piece of wood to be cut at the stop rail (16) and
on the turntable (14).
• Secure the material with the clamping device (7) on the fixed
saw table (15) to prevent it from shifting during the cutting
process.
NOTE: Only use the left clamping device (7)!
• Release the lock switch (3) and press the ON/OFF switch
(2) to start the motor. (Refer also to point 10.2 "Changing
the speed" in this regard.)
• With the drag guide (21) fixed in place (21):
Use the handle (1) to move the machine head (4) steadily
and with light pressure downwards until the saw blade (6)
has completely cut through the work piece.

• With the drag guide (21) not fixed in place (21):

Pull the machine head (4) all the way to the front. Lower the
handle (1) to the very bottom by applying steady and light
downward pressure. Now push the machine head (4) slowly
and steadily to the very back until the saw blade (6) has
completely cut through the work piece.
• When the cutting operation is completed, move the machine
head back to its upper (home) position and release the ON/
OFF button (2).
Attention! The machine executes an upward stroke auto-
matically due to the return spring, i. e. do not release the han-
dle (1) after completing the cut; instead allow the machine
head to move upwards slowly whilst applying light counter
pressure.
10.5 Crosscut 90° and turntable 0° - 45°
(fig. 1/8/9)
The multifunction sliding cross cut mitre saw can be used to
make crosscuts of 0° -45° to the left and 0° -45° to the right
in relation to the stop rail.
Attention! For 90° crosscuts, the moveable stop rail (16a)
must be fixed in the inner position.
• Open the set screw (16b) for the moveable stop rails (16a)
and push the moveable stop rails (16a) inwards.
• The moveable stop rails (16a) must be locked so that the
distance between the stop rails (16a) and the saw blade (6)
is no more than 8 mm.
• Before making the cut, check that no collision can occur be-
tween the stop rails (16a) and the saw blade (6).
• Secure the set screw (16b) again.
• Loosen the locking handle (11) if tightened. Pull up the
latched position lever (35) with your index finger and use
the locking handle (11) to set the rotary table (14) to the
desired angle (fig. 3.3+4).
• The pointer (12) on the rotary table must match the desired
angle on the scale (13) on the fixed saw table (15).
• Re-tighten the locking handle (11) to secure the rotary table (14)
(fig. 3.3+4).
• Cut as described under section 10.4.
10 GB
10.6 Mitre cut 0°- 45° and turntable 0°
(fig. 1, 7-10)
The multifunction sliding cross cut mitre saw can be used to
make mitre cuts of 0° - 45° in relation to the work face.
Attention! For 0°- 45° mitre cuts, the clamping device (7)
must only be mounted on the right side (see fig. 14-15).
Attention! For mitre cuts (inclined saw head), the moveable
stop rail (16a) must be fixed in the outer position (left side).
• Open the set screw (16b) for the moveable stop rails (16a)
and push the moveable stop rails (16a) outwards.
• The moveable stop rails (16a) must be locked so that the
distance between the stop rails (16a) and the saw blade (6)
is no more than 8 mm.
• The moveable stop rail (16a) must be fixed in the inner posi-
tion (right side).
• Before making the cut, check that no collision can occur be-
tween the stop rails (16a) and the saw blade (6).
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22).
• Use the handle (1) to angle the machine head (4) to the left,
until the pointer (19) indicates the desired angle measure-
ment on the scale (18).
• Re-tighten the set screw (22).
• Cut as described in section 10.4.
10.7 Mitre cut 0°- 45° and turntable 0°- 45°
(fig. 1/8/10)
The multifunction sliding cross cut mitre saw can be used to
make mitre cuts to the left of 0°- 45° in relation to the work
face and, at the same time, 0° - 45° to the left or 0° - 45° to
the right in relation to the stop rail (double mitre cut).
Attention! For 0°- 45° mitre cuts, the clamping device (7)
must only be mounted on the right side (see fig. 14-15).
Attention! For mitre cuts (inclined saw head), the moveable
stop rail (16a) must be fixed in the outer position (left side).
• Open the set screw (16b) for the moveable stop rails (16a)
and push the moveable stop rails (16a) outwards.
• The moveable stop rails (16a) must be locked so that the
distance between the stop rails (16a) and the saw blade (6)
is no more than 8 mm.
• Before making the cut, check that no collision can occur be-
tween the stop rails (16a) and the saw blade (6).
• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Fold the locking handle (11) upwards to loosen the rotary
table (14) (fig. 3.3+4).
• Set the rotary table (14) to the desired angle (refer also to
point 10.5 in this regard).
• Fold the locking handle (11) downwards to secure the rotary
table (14) (fig. 3.3+4).
• Undo the set screw (22).
• Use the handle (1) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 10.6).
• Re-tighten the set screw (22).
• Cut as described under section 10.4.