Knowing Your New Food Dehydrator; Operating Panel; Properties Of Your New Food Dehydrator - Gastroback Design Dörrautomat Pro Bedienungsanleitung

KNOWING YOUR NEW FOOD DEHYDRATOR

3

Operating panel

6 7 8
1 OPERATING PANEL
2 Stainless steel HOUSING with HANDLES at both sides for easy moving the appliance
3 DOOR with viewing window: for closing the dehydration chamber during operation
4 DEHYDRATION CHAMBER with low-noise FAN ASSEMBLY at the rear and 6 or 10 SHELVES for
holding inserts
5 ON/OFF SWITCH on the back of the appliance: increases safety and avoids useless energy loss, when
the appliance is in standby mode
OPERATING PANEL holding the following elements:
6 "START/STOP" BUTTON: for starting or stopping operation
7 "TIME/TEMP" BUTTON: press here to select the temperature or time for adjustment
8 DISPLAY: showing the count down of the dehydrating time or the set temperature
9 ADJUSTING BUTTONS "+" and "–": touch these buttons for setting the desired value
INSERTS AND ACCESSORIES
10 Stainless steal wire mesh FOOD TRAY 6 or 10 trays
11 PLASTIC TABLET suited for covering the bottom of the dehydration chamber. You may use it also for your
preparations and for drying very small pieces or delicate food that may crumble, when dehydrated
12 PLASTIC TRAY for very soft food and small pieces
13 SILOCONE MUESLI PAN for making muesly bars and drying seasoning paste
14 PEELER only included in delivery with the 46603 Design Food Dehydrator Max
EN
36
1
2
4
5
9

PROPERTIES OF YOUR NEW FOOD DEHYDRATOR

Your new food dehydrator is intended for drying almost all types of fresh food. For this,
the fan assembly at the rear of the dehydration chamber provides a constant flow of
warm air with variable temperature. The especially designed fan minimizes the noise
during operation.
• Due to the horizontal air flow within the dehydration chamber, merging the fla-
vours of food on the different food trays into each other is avoided as far as possi-
ble. You may insert, exchange, or take out the food trays any time you like, even
during operation. Leaving some shelves empty will not influence the dehydrating
performance. An even drying performance is enabled via the constant tempera-
ture and air flow within the complete dehydration chamber. Provided that the air
can flow without obstacles, in most cases, it does not matter, how your food is
10
arranged within the dehydration chamber. In rare cases, you may turn the com-
plete food trays or even swap the food trays with each other within the dehydra-
tion chamber. Simply keep the door of the dehydration chamber closed during
operation.
• The appliance is controlled via touch bottons, providing a smooth and even sur-
face for easy cleaning. Additionally, there is no need to press on the buttons.
Simply touch them. The appliance confirms each entry via an acoustic signal.
11
Dehydrating time and temperature can be adapted to the type and freshness of
your food, the thickness of the slices and pieces and the desired consistency (see:
'Tips for Best Results / Preparating Your Food'). You may change these operating
parameters any time you like, even during operation.
• The remaining dehydrating time is displayed as a count down. When the count
down reaches zero ("00:00"), the appliance cancels operation automatically and
switches back to standby.
12
• The temperature unit may be toggled from °C to °F and vice versa (see: 'Opera-
tion / Changing the Temperature Unit').
• An overheat protection device improves the operational safety, while the appli-
ance is operated for several hours.
• A separate On/Off switch at the rear provides additional safety during your pre-
parations and breaks. However, when you do not intend to operate the appli-
13
ance for several hours and days, always unplug the appliance. As an additional
benefit, in general, this will protect electronically controlled appliances from over-
voltage caused by the power supply, and therefore ensures a prolonged lifetime.
IMPORTANT - Do not let the appliance operate continuously for more than 24
hours. After each 24 hours of operation, unplug the appliance and make a break
14
of at least 2 hours for prolonging the lifetime of the fan assembly.
EN
37