Cleaning, Maintenance And Storage; Disposal And Recycling - Scheppach WSE850 Originalbetriebsanleitung

This is the best method of igniting an arc.
Check that you have the correct electrode and cur-
rent strength on a test part.
Electrode Ø (mm)
1,6
2
2,5
Important!
Do not dab the workpiece with the electrode since it could
be damaged, making it more difficult to ignite the arc.
As soon as the arc has ignited, attempt to keep it a
distance from the workpiece equivalent to the diam-
eter of the electrode. This distance should be kept
as constant as possible during the welding process.
The angle of the electrode in the direction in which
you are working should be 60° (fig. 5).
Important!
Always use tongs to remove spent electrodes and to
move parts that you have just welded. Please note
that the electrode holder (8) must always be put down
so that it is insulated after you have completed the
welding work.
Do not remove the slag until the weld has cooled.
If you want to continue a weld after an interruption,
the slag from your initial attempt must first be re-
moved.
Overheating guard
The welding set is fitted with an overheating guard
that protects the welding transformer from overheat-
ing. If the overheating guard trips, the control lamp
(4) on your set will be lit. Allow the welding set to
cool for a time.

9. Cleaning, maintenance and storage

Remove the power plug and wait until the fan has
stopped and the machine has completely cooled
down before performing any cleaning or maintenance
tasks.
Cleaning
• Remove dust and dirt from the machine at regular
intervals. Cleaning is best carried out with com-
pressed air, a fine brush or a cloth.
• We recommend that you clean the device immedi-
ately each time you have finished using it.
Maintenance
Before every start of work:
• Check the unit function. Do not work with a defec-
tive unit.
• Check the cable for damage and replace it with a
cable of the same quality if necessary.
• There are no parts inside the equipment which re-
quire additional maintenance.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Welding current (A)
40 – 50
40 – 80
60 – 110
Storage
1. Clean the exterior housing of the machine.
2. Make sure that the machine is unplugged. Remem-
ber that also the electrodes should be stored at a
dry place.
3. Store the machine in a cold, dry place where it is
out of the reach of children, ignition sources and
inflammable substances.
Ordering replacement parts
Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: electrode holder, ground terminal
* Not necessarily included in the scope of delivery!

10. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic. De-
fective components must be disposed of as special
waste. Ask your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical
and electronic equipment (WEEE). This product must
be disposed of at a designated collection point. This
can occur, for example, by handing it in at an author-
ised collecting point for the recycling of waste elec-
trical and electronic equipment. Improper handling
of waste equipment may have negative consequenc-
es for the environment and human health due to po-
tentially hazardous substances that are often con-
tained in electrical and electronic equipment. By
properly disposing of this product, you are also con-
tributing to the effective use of natural resources.
You can obtain information on collection points for
waste equipment from your municipal administration,
public waste disposal authority, an authorised body
for the disposal of waste electrical and electronic
equipment or your waste disposal company.
GB І 21