Transport; Maintenance - Scheppach HM100LXU Original Bedienungsanleitung

• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the set
screw (26).
• Using the handle (11), set the rotary table (14) to
the desired angle (refer also to point 8.4 in this
regard).
• Re-tighten the set screw (26) in order to secure
the rotary table.
• Undo the locking screw (22) and use the handle
(1) to tilt the machine head (4) to the left until it co-
incides with the required angle value (in this con-
nection see also section 8.6).
• Re-tighten the fixing screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3/14)
• The cutting depth can be infinitely adjusted using
the screw (24). To do this loosen the knurled nut on
the screw (24). Move the stop for the cutting depth
limitre (25) to the outside. Turn the screw (24) in
or out to set the required cutting depth. Then re-
tighten the knurled nut on the screw (24).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1)
The saw is equipped with a debris bag (17) for saw-
dust and chips.
Squeeze together the metal ring on the dust bag
and attach it to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a
zipper at the bottom.
8.10 Changing the saw blade (Fig. 15/16/17/18)
Remove the power plug!
Important.
Wear safety gloves when changing the saw
blade. Risk of injury!
• Swing up the machine head (5).
• Undo the screw (e) on the guide bar (37), so that it
can move freely and be pivoted downwards.
• Press the release lever (3). Swing up the saw
blade guard (6) to the point where the recess in the
saw blade guard (6) is above the flange bolt (31).
• Press the saw shaft lock (4) with one hand. With
the other hand insert the allen key (d) in the flange
bolt (31).
• Hold the Allen key (d) and slowly close the saw
blade guard until it touches the Allen key.
• Firmly press the saw shaft lock (4) and slowly ro-
tate the flange bolt (31) in clockwise direction. The
saw shaft lock (4) engages after no more than one
rotation.
• Now, using a little more force, slacken the flange
bolt (31) in the clockwise direction.
• Turn the flange screw (31) right out and remove the
external flange (32).
• Take the blade (7) off the inner flange (38) and pull
out downwards.
28 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
• Carefully clean the flange screw (31), outer flange
(32) and inner flange (38).
• Fit and fasten the new saw blade (7) in reverse or-
der.
• Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade
(7) must coincide with the direction of the arrow
on the housing.
• Move the guide bar (37) into position and tighten
the screw (e) again.
• Before continuing your work make sure that all
safety devices are in good working condition.
• Important! Every time that you change the saw
blade (7), check to see that it spins freely in the
table insert (11) in both perpendicular and 45° an-
gle settings.
• Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser (Fig. 3/19/20)
• To switch on: Move the ON/OFF switch of the la-
ser (34) to the "1" position. A laser line is projected
onto the material you wish to process, providing an
exact guide for the cut.
• To switch off: Move the ON/OFF switch of the la-
ser (34) to the "0" position.
• Replacing the battery: Switch off the laser (33).
Remove the battery compartment cover (36). Re-
move the batteries and replace with new batteries
(2 x 1.5 Volt Type LR 03 Micro, AAA) Check that
the battery terminals are positioned correctly when
inserting new batteries. Close the battery compart-
ment (35) again.
8.12 Adjusting the laser (Fig. 21)
If the laser (33) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (38) and set the laser by moving sideways to
that the laser beam strikes the teeth of the saw blade
(6).

9. Transport

• Tighten the set screw (26) in order to lock the ro-
tary table (14)
• Activate the release lever (3), press the machine
head (4) downwards and secure with the safety pin
(23). The saw is now locked in its bottom position.
• Fix the saw's drag function with the locking screw
for drag guide (20) in rear position.
• Carry the equipment by the fixed saw table (15).
• When reassembling the equipment proceed as de-
scribed under section 7.1.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!