Scheppach HM100LXU Original Bedienungsanleitung Seite 23

10 Connect the dust extraction device
If connections for dust extraction and a collect-
–
ing device are present, make sure that they are
connected and used properly.
Operation in enclosed areas is only permitted
–
with a suitable extraction system.
11 Do not use the cable for purposes for which it is
not intended
Do not use the cable to pull the plug out of the
–
outlet. Protect the cable from heat, oil and sharp
edges.
Secure the workpiece
12
– Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held
more securely than with your hand.
An additional support is necessary for long
–
workpieces (table, trestle, etc.) in order to pre-
vent the machine from tipping over.
– Always press the workpiece firmly against
the working plate and stop in order to prevent
bouncing and twisting of the workpiece.
Avoid abnormal posture
13
Make sure that you have secure footing and al-
–
ways maintain your balance.
Avoid awkward hand positions in which a sud-
–
den slip could cause one or both hands to come
into contact with the saw blade.
Take care of your tools
14
Keep cutting tools sharp and clean in order to
–
be able to work better and more safely.
Follow the instructions for lubrication and for
–
tool replacement.
– Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
Check extension cables regularly and replace
–
them when damaged.
Keep the handle dry, clean and free of oil and
–
grease.
15 Pull the plug out of the outlet
Never remove loose splinters, chips or jammed
–
wood pieces from the running saw blade.
During non-use of the electric tool or prior to
–
maintenance and when replacing tools such as
saw blades, bits, milling heads.
16 Do not leave a tool key inserted
Before switching on, make sure that keys and
–
adjusting tools are removed.
Avoid inadvertent starting
17
Make sure that the switch is switched off when
–
plugging the plug into an outlet.
Use extension cables for outdoors
18
– Only use approved and appropriately identified
extension cables for use outdoors.
Only use cable reels in the unrolled state.
–
Remain attentive
19
Pay attention to what you are doing. Remain
–
sensible when working. Do not use the electric
tool when you are distracted.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
20 Check the electric tool for potential damage
Protective devices and other parts must be care-
–
fully inspected to ensure that they are fault-free
and function as intended prior to continued use
of the electric tool.
– Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-
free operation of the electric tool.
The moving protective hood may not be fixed in
–
the open position.
– Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
fied in the operating manual.
Damaged switches must be replaced at a cus-
–
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
Do not use any electric tool on which the switch
–
cannot be switched on and off.
ATTENTION!
21
Exercise elevated caution for double mitre cuts.
–
ATTENTION!
22
– The use of other insertion tools and other ac-
cessories can entail a risk of injury.
Have your electric tool repaired by a qualified
23
electrician
This electric tool conforms to the applicable
–
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
ADDITIONAL SAFETY INSTRUCTIONS
Safety precautions
1
Warning! Do not use damaged or deformed saw
–
blades.
– Replace a worn table insert.
Only use saw blades recommended by the man-
–
ufacturer which conform to EN 847-1.
Make sure that a suitable saw blade for the ma-
–
terial to be cut is selected.
Wear suitable personal protective equipment.
–
This includes:
Hearing protection to avoid the risk of becom-
–
ing hearing impaired,
Respiratory protection to avoid the risk of
–
inhaling harmful dust,
Wear gloves when handling saw blades and
–
rough materials. Carry saw blades in a con-
tainer whenever practical.
Wear goggles. Sparks generated during work
–
or splinters, chippings and dust coming from
the device can lead to loss of eyesight.
GB 23