Technical Data; Assembly - Scheppach HA1600 Original Anleitungen

ter you have completed any repairs or maintenance
work.
• Be sure to observe the safety information and op-
erating and maintenance instructions issued by the
manufacturer, as well as the dimensions listed in
the Technical Data.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Note the information published by your profession-
al associations.
• Do not use any low-powered machines for heavy
duty work.
• Do not mis-use the cable
• Make sure you stand squarely and keep your bal-
ance at all times.
• Check that the moving parts are in good working
order, that they do not jam, and that no parts are
damaged. Make sure that all parts are fitted cor-
rectly and that all other operating conditions are
properly fulfilled.
• Unless otherwise stated in the operating instruc-
tions, damaged safety devices and parts have to
be repaired or replaced by an authorized service
center.
• Have damaged switches replaced by a customer
service workshop.
• This electric tool complies with the pertinent safety
regulations. Repairs are to be carried out only by
a qualified electrician using original replacement
parts or the user may suffer an accident.
• If necessary, wear suitable personal protection
equipment. This could consist of:
- Ear-muffs to prevent the risk of damaging your
hearing
- A breathing mask to prevent the risk of inhaling
hazardous dust
• The operator has to be informed about the condi-
tions with an influence on noise development.
• Faults on the machine have to be reported to the
person in charge as soon as they are discovered.
• This appliance is not suitable for the collection of
dangerous dust.
• This equipment is not designed to be used by peo-
ple (including children) with limited physical, sen-
sory or mental capacities or those with no experi-
ence and/or knowledge unless they are supervised
by a person who is responsible for their safety or
they have received instructions from such a person
in how to use the equipment safely. Children must
always be supervised in order to ensure that they
do not play with the equipment.
Remaining hazards
The machine has been built using modem technology
in accordance with recognized safety rules.Some re-
maining hazards, however, may still exist.
• Wood chips and sawdust can be health hazards.
Be sure to wear personal protective gear such as
safety goggles and a dust mask.
• Dust inhalation may occur when closing and re-
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
placing the dust bag.
• Please note the instructions concerning proper dis-
posal in the operating manual (e.g. the use of P2
dust masks) to prevent dust inhalation.
• Noise can be a health hazard. The permitted noise
level is exceeded when working. Be sure to wear
personal protective gear such as ear protection.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by following
the instructions in "Safety Precautions", "Proper
Use" and in the entire operating manual.
Keep this safety information in a safe place.

6. Technical data

Technical Data
Dimensions L x W x H
(mm):
Overall height with
filter bag mm
Ectractor duct
connections ø mm
Hose length mm
Wheel diameter mm
Approx. weight kg
Rate of air flow m /h
3
Pressure differential
Pa
Filter aera (filter bag)
m
2
Sawdust bag capacity
litres
Performance
Electric motor
Nominal input P1
Output power P2
Motorspeed 1/min.
Work Place Emissions Values:
Empty Run Noise dB
(A)
Working Noise dB (A)

7. Assembly

For packaging reasons your machine is delivered in
semi-assembled state.
• Attach the side covering loosely to the base frame
using flat-head screws M8 x 40 mm and screw
nuts. Do not tighten completely. Fig. 2, 3
• Attach the cross-member to the side covering left
and right with flat-head screws M 8 x 12 and screw
nuts. Fig. 4, 5
• Remove all screws and nuts form the housing.
• Attach the housing to the side coverings using flat-
head screws M5 x 20 and screw nuts. Securely
tighten all nuts. Fig. 6
GB
830 x 520 x 1600
1600
100
2200
150
20
1150
1600
approx. 1
75
220-240 V/5O Hz
0,55 kW
0,34 kW
2850
75,5
75,5
17 / 24