Technical Data; Installation - Scheppach PN-NTS20 Bedienungsanleitung

the appliance materials to corrode.
m WARNING!
This electric tool generates an electromag-
netic field during operation. This field can
impair active or passive medical implants
under certain conditions. In order to pre-
vent the risk of serious or deadly injuries,
we recommend that persons with medical
implants consult with their physician and the
manufacturer of the medical implant prior to
operating the electric tool.

7. Technical Data

Mains voltage
Power
Water tank capacity
Suction performance
Protection category
Protection class

8. Installation

m IMPORTANT!
Prior to use, ensure that the device has
been correctly and fully assembled.
Unpacking (Fig. 1+2+3)
1 Release the locking hooks (4) and remove
the machine head (2). The accessories
are located inside the stainless steel con-
tainer (7). Only the plastic extension tubes
(3x) (7) are located outside the stainless
steel container, in the packaging. Remove
all of the accessories from the stainless
steel container (7).
Installing the castors (fig. 4)
1. Press the four castors (5) into the ho-
les in the castor mounts.
Installing the machine head (2) (Fig. 5)
1 Place the machine head (2) on the stain-
less steel container (7). Secure the ma-
chine head (2) with the locking hooks (4).
When installing the machine head (2), en-
sure that the locking hooks (4) latch into
place correctly.
Installing the foam filter (14) (fig. 6)
Never use the device without filter! Always
ensure that the filters are correctly fitted!
Installing the foam filter (14): For wet vacu-
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
220-240V~
50/60Hz
1200W
20L
17 kPA
IP24
II
uming, slide the foam filter (14) provided
over the filter basket with safety float valve
(12).
Installing the paper filter bag (15) (fig. 7)
It is recommended to use an additional pa-
per filter bag (15) when vacuuming fine, dry
dirt. Slide the paper filter bag (15) over the
suction opening in the stainless steel con-
tainer (7). The paper filter bag (15) is only
suitable for dry vacuuming. The paper filter
bag (15) makes it easier to dispose of the
dust collected.
Installing the suction hose (fig. 8 + 9)
Connect the suction hose (13) to the cor-
responding port, depending on the desired
use, on the wet and dry vacuum.
Vacuuming:
Connect the suction hose (13) to the suction
hose port (8). To do so, slide the end of the
suction hose (13) into the suction hose port
(8). Make sure the plug-in fitting on the end
of the suction hose (13) latches into the re-
cess on the suction hose connection (8). In
the end position, turn the suction hose (13)
in a clockwise direction.
Blowing:
Connect the suction hose (13) to the suction
hose port (11). Make sure the plug-in fitting
on the end of the suction hose (13) latches
into the recess on the connection with blast
function (11). In the end position, turn the
suction hose (13) in a clockwise direction.
Installing the plastic extension tubes,
suction hose and floor nozzle (fig. 10)
Assemble the plastic extension tubes (18) by
pushing them together. Connect the assem-
bled plastic extension tubes with the bent
end of the suction hose (13).
Fit the floor nozzle (16) or joint nozzle (17) to
the other end of the assembled plastic ex-
tension tubes.
GB 17