Installation; Equipment; Commissioning; Operating Instructions - Scheppach mts 355s Originalanleitung

Prepare the workplace where you intend to place the electrical power tool. Provide enough space to ensure safe and trouble-free operation. The
power tool is designed for working in enclosed rooms and has to be installed on level and firm ground.
Mount the unit on the workbench, by attaching it to the holes provided.
1 Machine head
2 Switch locking knob
3 On/off switch
4 Handle
5 Claming handle
6 Clamping jaw, flexible
• Know the machine. Learn its applications
and limitations, as well as the specific
potential hazards.
• Check for damage if part of the machine is
damaged, it should be carefully inspected
to ensure that it can perform its intended
function correctly. If in doubt, the part should
be replaced.
• Be sure the switch is OFF before plugging In.
• Make sure tool has been cleaned and
properly lubricated.
• Check for damaged parts. Before using any
tool, any part that appears damaged should
be carefully checked to determine that it will
operate properly and perform its intended
function.
• Check for alignment and binding of all
moving parts, broken parts or mounting
fixtures and any other condition that may
GB
affect proper operation. Any part that is
langsam schnell
Changing the speed (Fig. 1)
vitesse lente vitesse rapide
The saw has 2 speed ranges:
slow fast
Setting the depth stop (see Fig. 8)
Pomalu rychle
The downward movement of the machine can
be adjusted through the depth gauge (E).
Pomalý rýchly
To compensate the wear of the disc a sub-
Počasnega hitrega
lassú gyors
• The cutting disc should be fitted perfect-
ly and should turn freely. Have a trial run
without any load for 1 minute at least. Do not
бавно бързо
use a disc that is damaged, non-circular or
vibrating.
• Set up the depth stop (see Setting the depth
Nopea hidas
stop) properly. If the stop is not set up cor-
rectly, the disc may cut the surface under the
base plate.
• During the operation, the cutting disc cover
should be in place and the swinging protec-
tive cover should work as appropriate.
• Do not cut any material with asbestos or
magnesium content.
• Protect the disc from any blows, hits and
grease.
• Do not conduct the machine to the work

Installation

Equipment Fig. 1+6
7 Clamping jaw, fixed
8 Quick clamping lever
9 Locking bolt
10 Guard, flexible
11 Guard, fixed

Commissioning

damaged should be properly repaired or
replaced by a qualified technician.
• Do not use the tool if any switch does not
turn off and on properly.
• Never force the tool or attachment to do the
work of a larger industrial tool. It is designed
to do the job better and more at the rate for
which it was intended.
• Always unplug the cord by the plug. Never
yank the cord out of the wall.
• Always turn off the machine before
unplugging.
• With normal use, the motor housing may get
hot.
• Make all adjustments to the machine with the
power OFF.
• Never leave the cutting off wheel saw
unattended while it is running.
• When turning off the machine, never leave
• To operate the saw at a speed of 1000 rpm
(metal), set the switch (14) to position I.
sequent adjustment of the cutting depth is
possible.
Loosen the lock nut (F).
Set the depth stop (E) accordingly.

Operating instructions

piece unless it is on.
• Keep your hands out of the reach of the
rotating disc.
• Sparks are produced by cutting metals. Look
out for nobody being at risk. No flammable
materials should be situated in adjacent area
(the reach of sparks).
• The disc jam results in the machine jerky
response. If that is the case, switch the ma-
chine off immediately.
• Do not ram the disc in the work piece and do
not put excessive pressure on the machine.
Avoid possible jam of the disc when working
in corners, sharp edges etc. If the disc gets
damaged in result of incorrect use, stress
cracking may form, which results in the disc
crack without any warning.
16
12 Locking chain (transport)
13 Ring spanner (8 mm)
(cut-off wheels replacement)
14 Switch for switching speeds
the cutting off wheel saw until it has come to
a complete stop.
• Make every effort to prevent snagging
by exercising special care when working
corners, sharp edges, ragged welds, etc.
• Do not use a cutting off wheel that is not in
accordance with specified sizes.
• Never carry the tool by the cord.
• Don't pour water or coolant on cutting off
wheel when cutting.
• Make sure to secure cutting material so it
does not move during operation.
• Cutting material can get extremely hot during
operation.
If there is any question about a condition
about a condition being safe or unsafe, do not
operate the tool.
• To operate the saw at a speed of 3500 rpm
(wood), set the switch (14) to position II.
Lower the machine head and check whether
there is enough distance between the blade
and fixed jaw (7).
Tighten the lock nut (F) tightly.
• Prevent the motor overloading, particularly
when working large pieces. Hold the hand-
grip with a light pressure only when cutting.
Mind the size of the cutting disc. The hole
diameter should correspond to the machine
spindle without any free travel. Do not use
any adapters and transition pieces.
m Caution!
• After the machine is switched off, the cutting
disc will still be running out.
• The spindle lock should not be touched until
the disc stops completely.
• The cutting disc and the piece to be cut are
very hot when operation is going on. Do not
touch them before they cool down.