General Information; General Safety Information - Scheppach mts 355s Originalanleitung

• After unpacking, check all parts for possible
transportation damages. In the event of
complaints, inform the supplier immediately.
Any complaints made after this time will not
be accepted.
• The shipment is to be checked for complete-
ness upon receipt.
• Read through the manual carefully in order
to make yourself familiar in dealing with the
device before using it for the first time.
• Only use original equipment regarding ac-
cessories, as well as consumable items and
spare parts. Spare parts can be obtained
from your specialized dealer.
When ordering, please specify our part num-
bers, as well as type and construction year of
the device.
NOTE:
According to the applicable product liability
laws, the manufacturer of the device does not
assume liability for damages to the product or
damages caused by the product that occurs
Attention! The following basic safety measures must be observed when using electric tools for protection against electric shock, and the risk
of injury and fire. Read all these notices before using the electric tool and keep the safety instructions for later reference.
1 Keep the work area orderly
– Disorder in the work area can lead to
accidents.
2 Take environmental influences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or
GB
wet environment.
– Make sure that the work area is well-
illuminated.
– Do not use electric tools where there is a
risk of fire or explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts
(e.g. pipes, radiators, electric ranges,
cooling units).
4 Keep children away
– Do not allow other persons to touch the
equipment or cable, keep them away
from your work area.
5 Securely store unused electric tools
– Unused electric tools should be stored in
a dry, elevated or closed location out of
the reach of children.
6 Do not overload your electric tool
– They work better and more safely in the
specified output range.
7 Use the correct electric tool
– Do not use low-output electric tools for
heavy work.
– Do not use the electric tool for purposes
for which it is not intended. For example,
do not use handheld circular saws for
the cutting of branches or logs.
– Do not use the electric tool to cut fire-
wood.
8 Wear suitable clothing
– Do not wear wide clothing or jewellery,
which can become entangled in moving
parts.
– When working outdoors, anti-slip foot-
wear is recommended.

General information

due to:
• Improper handling,
• Non-compliance of the operating instruc-
tions,
• Repairs by third parties, not by authorized
service technicians,
• Installation and replacement of non-original
spare parts,
• Application other than specified,
• A breakdown of the electrical system that
occurs due to the non-compliance of the
electric regulations and VDE regulations
0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the
operating instructions before installing and
commissioning the device. The operating
instructions are intended to help the user to
become familiar with the machine and take
advantage of its application possibilities in
accordance with the recommendations. The
operating instructions contain important infor-
mation on how to operate the machine safely,
General safety information m
– Tie long hair back in a hair net.
9 Use protective equipment
– Wear protective goggles.
– Wear a mask when carrying out dust-
creating work.
10 Do not use the cable for purposes for
which it is not intended
– Do not use the cable to pull the plug
out of the outlet. Protect the cable from
heat, oil and sharp edges.
11 Secure the workpiece
– Use the clamping devices or a vice to
hold the workpiece in place. In this man-
ner, it is held more securely than with
your hand.
– An additional support is necessary for
long workpieces (table, trestle, etc.) in
order to prevent the machine from tip-
ping over.
– Always press the workpiece firmly
against the working plate and stop in
order to prevent bouncing and twisting
of the workpiece.
12 Avoid abnormal posture
– Make sure that you have secure footing
and always maintain your balance.
– Avoid awkward hand positions in which
a sudden slip could cause one or both
hands to come into contact with the saw
blade.
13 Take care of your tools
– Keep cutting tools sharp and clean in
order to be able to work better and more
safely.
– Follow the instructions for lubrication
and for tool replacement.
– Check the connection cable of the elec-
tric tool regularly and have it replaced
by a recognised specialist when dam-
aged.
– Check extension cables regularly and
14
professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and
how to increase reliability and service life of
the machine.
In addition to the safety regulations in the
operating instructions, you have to meet the
applicable regulations that apply for the ope-
ration of the machine in your country.
Keep the operating instructions package
with the machine at all times and store it in a
plastic cover to protect it from dirt and mois-
ture. Read the instruction manual each time
before operating the machine and carefully
follow its information. The machine can only
be operated by persons who were instructed
concerning the operation of the machine
and who are informed about the associated
dangers. The minimum age requirement must
be complied with.
We have marked the points in this manual
that concern your safety with this sign m
replace them when damaged.
– Keep the handle dry, clean and free of
oil and grease.
14 Pull the plug out of the outlet
– Never remove loose splinters, chips or
jammed wood pieces from the running
saw blade.
– During non-use of the electric tool or
prior to maintenance and when replac-
ing tools such as saw blades, bits,
milling heads.
– When the saw blade is blocked due to
abnormal feed force during cutting, turn
the machine off and disconnect it from
power supply. Remove the work piece
and ensure that the saw blade runs free.
Turn the machine on and start new cut-
ting operation with reduced feed force.
15 Do not leave a tool key inserted
– Before switching on, make sure that
keys and adjusting tools are removed.
16 Avoid inadvertent starting
– Make sure that the switch is switched off
when plugging the plug into an outlet.
17 Use extension cables for outdoors
– Only use approved and appropriately
identified extension cables for use
outdoors.
– Only use cable reels in the unrolled
state.
18 Remain attentive
– Pay attention to what you are doing.
Remain sensible when working. Do
not use the electric tool when you are
distracted.
19 Check the electric tool for potential dam-
age
– Protective devices and other parts
must be carefully inspected to ensure
that they are fault-free and function as
intended prior to continued use of the