Time-Based Blast Chilling/Blast Freezing; Time-Based Soft Blast Chilling - coldline W5T Bedienungs- Und Wartungsanleitungen

Shortcut commands while in standby mode Shortcut commands while in standby mode Shortcut commands while in standby mode Shortcut commands while in standby mode
1
Blast freezing
Detailed commands sequence Detailed commands sequence: : : : Detailed commands sequence Detailed commands sequence
1. Make sure the appliance is in standby
2. Insert the needle probe in the product to be chilled (10.0
3. Press button to select the blast freezing cycle.
• The led button
• Display DY1 DY1 gives the setpoint of the air in the compartment (- - - - 38°C
DY1 DY1
• Display DY2 DY2 reads "---
DY2 DY2
4. Press button to start the blast freezing cycle.
• The led button
The compressor only starts working 5
•
• DY1 DY1 DY1 gives needle probe temperature, and DY2 DY1
minutes.
• If you press button
5. A buzzer sounds to advise that the blast chilling cycle has finished.
6. At the end of the cycle, holding mode starts and continues indefinitely at a holding temperature of - - - - 20°C
• The led button
• If you press button
how long it took.
The holding stage must last only as long as strictly necessary.
•
7. To exit holding mode, press button
• The led button
The compressor stops 5 5 5 5 seconds after button
•
Important Important Important Important
• Countdown starts when core temperature measured by the needle probe drops below +65°C.
• When a blast freezing cycle is started, the compressor works non-stop until air temperature in the
compartment reaches - - - - 38°C
• The blast freezing cycle ends when the product's core temperature measured by the needle probe reaches
- - - - 18°C. 18°C. 18°C. The cycle cannot last more than 240 minutes 18°C.

8.0 TIME-BASED BLAST CHILLING/BLAST FREEZING

8.1 TIME-BASED SOFT BLAST CHILLING

The time-based soft soft soft blast chilling cycle is controlled by the timer. soft
Shortcut commands while in standby mode Shortcut commands while in standby mode Shortcut commands while in standby mode Shortcut commands while in standby mode
1
Soft blast chilling
Detailed commands sequence: : : : Detailed commands sequence Detailed commands sequence Detailed commands sequence
1. Make sure the appliance is in standby
2. Press button to select the soft
• The led button
• Display DY1 DY1 gives the setpoint of the air in the compartment (- - - - 2°C DY1 DY1
2
standby mode (6.1
standby standby
comes on.
---".
--- ---
comes on.
working 5 seconds after key
working 5 working 5
while the cycle is running, you can view the time elapsed since it started.
flashes.
during holding time, you can view the time of the cycle just completed to see
.
goes off.
38°C. After this, it can cycle on and off to keep this temperature constant.
38°C 38°C
240 minutes. 240 minutes 240 minutes
2
standby mode (6.1
standby standby
soft blast chilling cycle. soft soft
comes on.
Start
6.1).
6.1 6.1
10.0).
10.0 10.0
38°C).
38°C 38°C
is pressed (pump-down 6 6 6 6 .4 .4 .4 .4)
DY2 the cycle time remaining, counting down from 240 DY2 DY2
is pressed (pump-down 6.4
Time-based cycle
6.1).
6.1 6.1
2°C). 2°C 2°C
6.4).
6.4 6.4
3
Start
240 240 240
20°C. 20°C 20°C
31