Temperature -Based Hard Blast Chilling; Temperature -Based Blast Freezing - coldline W5T Bedienungs- Und Wartungsanleitungen

Important Im Im Im portant portant portant
• Countdown starts when core temperature measured by the needle probe drops below +65°C.
• When a soft soft blast chilling cycle is started, the compressor works non-stop until air temperature in the
soft soft
compartment reaches - - - - 2°C
prevent frost from forming.
• The blast chilling cycle ends when the product's core temperature measured by the needle probe reaches
+3°C. +3°C. The cycle cannot last more than 90 minutes +3°C. +3°C.

7.2 TEMPERATURE -BASED HARD BLAST CHILLING

The temperature-based hard
Shortcut commands while in standby mode Shortcut commands while in standby mode Shortcut commands while in standby mode Shortcut commands while in standby mode
1
Hard blast chilling
Detailed commands sequence: : : : Detailed commands sequence
Detailed commands sequence Detailed commands sequence
1. Make sure the appliance is in standby
2. Insert the needle probe in the product to be chilled (10.0
3. Press button to select the hard blast chilling cycle.
• The led button
• Display DY1 DY1 DY1 gives the setpoint of the air in the compartment (- - - - 35°C DY1
• Display DY2 DY2 reads "---
DY2 DY2
4. Press button to start the hard blast chilling cycle.
• The led button
The compressor only starts working 5 5 5 5 seconds after key
•
• DY1 DY1 gives needle probe temperature, and DY2
DY1 DY1
minutes.
• If you press button
5. A buzzer sounds to advise that the blast chilling cycle has finished.
6. At the end of the cycle, holding mode starts and continues indefinitely at a holding temperature of +3
• The led button
• If you press button
how long it took.
The holding stage must last only as long as strictly necessary.
•
7. To exit holding mode, press button
• The led button
The compressor stops 5 5 5 5 seconds after button
•
Important Important Important Important
• Countdown starts when core temperature measured by the needle probe drops below +65°C.
• When a hard hard blast chilling cycle is started, the compressor works non-stop until air temperature in the
hard hard
compartment reaches - - - - 35
preventing the formation of frost.
• The blast chilling cycle ends when the product's core temperature measured by the needle probe reaches
+3°C. The cycle cannot last more than 90 minutes +3°C. +3°C. +3°C.

7.3 TEMPERATURE -BASED BLAST FREEZING

The temperature-based blast freezing cycle is controlled by the needle probe.
30
2°C. After this, it can cycle on and off to keep this temperature constant and
2°C 2°C
90 minutes. 90 minutes 90 minutes
hard blast chilling cycle is controlled by the needle probe. hard hard
2
standby mode (6.1
standby standby
comes on.
---".
--- ---
comes on.
while the cycle is running, you can view the time elapsed since it started.
flashes.
during holding time, you can view the time of the cycle just completed to see
.
goes off.
35°C °C. After this, it can cycle on and off to keep a constant temperature of - - - - 2°C
35 35 °C °C
90 minutes. 90 minutes 90 minutes
Start
6.1).
6.1 6.1
10.0). 10.0 10.0
35°C). 35°C 35°C
is pressed (pump-down 6.4
DY2 the cycle time remaining, counting down from 90
DY2 DY2
is pressed (pump-down 6.4
6.4).
6.4 6.4
90
90 90
+3°C
+3 +3
6.4).
6.4 6.4
2°C,
2°C 2°C
°C.
°C °C