Operation; Switching On/Off; Blast Chilling/Blast Freezing; Opening The Door While A Cycle Is Running - coldline W5T Bedienungs- Und Wartungsanleitungen

6.0 OPERATIONS

6.1 SWITCHING ON/OFF

Once you have turned on the appliance's power, the control panel (3.0
LEDs and displays come on for a few seconds, after which the display switches "OFF
still powered).
Switching on Switching on
Switching on Switching on
Hold button down for a few seconds: the appliance goes into standby
stands by to receive a command.
Display DY1 DY1 gives the temperature inside the appliance.
DY1 DY1
Display DY2 DY2 reads "--- DY2 DY2 ---". --- ---
Switching off Switching off
Switching off Switching off
Hold button down for a few seconds: the appliance switches "OFF
Display DY1 DY1 reads "OFF DY1 DY1 OFF OFF". OFF
Display DY2 DY2 stays off.
DY2 DY2

6.2 BLAST CHILLING/BLAST FREEZING

See points 7 7 7 7 .0 .0 .0 .0 and 8 8 8 8 .0 .0 .0 .0 for details.

6.3 OPENING THE DOOR WHILE A CYCLE IS RUNNING

If the door is opened while a blast chilling/blast freezing cycle is running, the "] ] ] ] - - - - [ [ [ [ " code will flash up
intermittently on display DY2
and only restart once the door is closed.
The blast chilling/blast freezing cycle cannot be started with the door open. If the door stays The blast chilling/blast freezing cycle cannot be started with the door open. If the door stays The blast chilling/blast freezing cycle cannot be started with the door open. If the door stays The blast chilling/blast freezing cycle cannot be started with the door open. If the door stays
open for longer than 30 seconds during the blast chilling/blast freezing cycle, the blast chilling open for longer than 30 seconds during the blast chilling/blast freezing cycle, the blast chilling open for longer than 30 seconds during the blast chilling/blast freezing cycle, the blast chilling open for longer than 30 seconds during the blast chilling/blast freezing cycle, the blast chilling
cycle is stopped. cycle is stopped. cycle is stopped. cycle is stopped.
6.4 PUMP DOWN
Pump- - - - down Pump Pump Pump down is a system designed to protect the compressor and its job is to avoid excessive working down down
pressures during start-up.
Stopping the compressor Stopping the compressor Stopping the compressor Stopping the compressor
When button is pressed to stop a blast chilling, blast freezing or holding cycle manually, the compressor
keeps working for 5 5 5 5 more seconds.

6.5 TEMPERATURE SENSOR AND NEEDLE PROBE READINGS

While a temperature-based cycle is running, DY1
view compartment sensor temperature by pressing the button relating to the cycle selected:
The value is put up on DY1 DY1 DY1 for 5 5 5 5 seconds. DY1
While a time-based cycle is running, DY1
view needle probe temperature by pressing button

6.6 HEATED NEEDLE PROBE (Optional extra)

The heated needle probe (optional extra) has a device that heats its tip, making it easier to pull out of frozen
products. Holding button
the probe can be easily removed from the frozen product. Heating only comes on if the door is open.

6.7 AUTOMATIC DEFROSTING

During operation, frost forms on the surface of the evaporator: this is normal but it reduces evaporator
efficiency. The purpose of defrosting is to restore full efficiency. Defrosting is performed automatically:
28
DY2 and, at the same time, a buzzer will sound. The compressor and fans inside stop
DY2 DY2
DY1 indicates the value
DY1 DY1
DY1 indicates the value
DY1 DY1
down for 5 5 5 5 seconds at the end of a blast freezing cycle turns on heating so that
3.0 3.0) automatically runs a lamp test. The 3.0
standby. During this phase, the machine standby standby
OFF OFF". OFF
the value measured by the needle probe. You can
the value the value
the value measured by the compartment sensor. You can
the value the value
. The value is put up on DY1
OFF" (control panel is off but OFF OFF
, or
DY1 for 5 5 5 5 seconds. DY1 DY1
.