Herunterladen Inhalt Inhalt Diese Seite drucken

Mounting The Bicycle Rack On The Trailer Tow Bar; Dismantling The Bicycle Rack - Eufab CROW PLUS Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Fit the spring washer (8a) onto the thread of the tension lever (8). Screw the
tension lever into the tension lever mount (7) of the quick closure, Figure
7. Screw the tension lever (8) into the tension lever mount (7) of the quick
closure. Turn the thread fully into the holder and tighten the tension lever
extension using a wrench (the tension lever has a spanner flat with a key
width of 17, see Figure 8).

5.2 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR

Ensure that the trailer tow bar is undamaged, clean and free of grease.
Remove any paint from the coupling ball.
Before you put the bicycle rack on the trailer tow bar, familiarise yourself
with the quick locking system.
The quick locking mechanism is a component with a tension lever (8).
Activating the lever opens or closes the quick locking mechanism. With the
help of the securing bolt (9) and the padlock (10), the quick locking system
may be locked and secured.
The padlock is always required when using the bicycle
rack. The bicycle rack may only be used if the padlock
is employed correctly and locked. The lock is safety-
relevant.
Park your vehicle on a level surface. Apply the handbrake.
Remove the securing bolt from the quick locking mechanism and rotate by
90° to prevent it from engaging again. Open the quick locking mechanism
by lifting the tension lever.
Place the rack, from above, horizontally onto the trailer tow bar. Push the
lever of the quick locking mechanism down (force required is approxima-
tely 35-40 kg) as far as it will go (the lever will remain in the horizontal
position).
Check whether the bike rack is securely and firmly positioned on the trailer
tow bar (and can no longer be rotated). If this is not the case, the quick
locking mechanism must be readjusted. Lift the lever and remove the rack
from the trailer tow bar. Remove the protective cap (11) of the adjusting
screw (13). Undo the counter nut (12) of the adjusting screw and rotate the
adjusting screw on the quick locking mechanism tighter by a quarter turn.
Then tighten the counter nut again.
Replace the rack back on the trailer tow bar and check whether the rack is
securely and firmly positioned on the trailer tow bar. Repeat the adjustment
process until the rack is secure and firm. Push the protective cap back onto
the adjustment screw.
10
11582_manual_ML_Eufab_EAL_11.2020_neu.indd 10
11582_manual_ML_Eufab_EAL_11.2020_neu.indd 10
Figure 9: Quick locking system
Figure 10: Padlock/protective cap
Figure 11: Adjustment screw
CAUTION
Always make sure that the counter nut on the
adjusting screw is correctly tightened!
Slight signs of pressure on the tow bar ball are normal
and do not influence the functionality.
When the rack can no longer be rotated on the trailer tow bar, rotate the
securing bolt of the quick locking mechanism until it engages. Now close
the quick locking mechanism with the supplied padlock and remove the key
from the lock. Store the key carefully and in a safe place. The bicycle rack is
now secured to prevent theft.
Regularly check the firm seating of the rack on the trailer tow bar as well
as the attachment of the bicycles to the rack. Also regularly check the
functions of the lighting system of your bicycle rack.

5.3 DISMANTLING THE BICYCLE RACK

In order to unfold the bicycle rack, start by swivelling the rear lights
outwards. The light mounts are clipped onto the rack table. Pull the
light mounts out of the clips. Pull the locking mechanism back (Position
1 in Figure 12). Hold the locking mechanism in this position. Swivel the
light mount out fully (Position 2 in Figure 12). Now release the locking
mechanism (Position 3 in Figure 12), the light mount is now secured to
prevent it from folding back in.
Figure 12: Locking the light mounts
Fold open the bicycle rack as shown in the following Figures.
1. Fold out the right rear light
2. Fold out the left rear light
3. Fold out the right wheel rail
4. Fold out the left wheel rail
04.11.20 14:10
04.11.20 14:10

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

11582

Inhaltsverzeichnis