Connected Repair [Core]; General Information; Configuration; Operation - Bosch ACS 753 Originalbetriebsanleitung

en | 56 | ACS 753 | Initial settings
i
Always check that the antennas, on the machine
side and on the workshop router side, are not ob-
structed by shielding or metallic materials in gener-
al and are not at an indicative distance greater than
10 m. If insufficient, it is recommended to improve
the coverage of the radio signal in the workshop
installing directional antennas or signal repeaters.
!
Make sure that the workshop network has active
security protocols (e.g.: WPA, WPA2) in order to
ensure data security.
5.18

Connected Repair [CoRe]

5.18.1

General information

Connected Repair, hereinafter CoRe, is a garage man-
agement system that allows to connect all the equip-
ment and computers in the same network to speed up
and improve the management, sharing and digitization
of data and services to be carried out on the vehicle.
Generally a CoRe network is formed by a server and a
number of clients equal to the number of PCs or de-
vices that can connect to it.
ACS 753 is to be considered as a client which is able
to autonomously connect to the CoRe server after hav-
ing configured the basic settings and exchange with it
the data necessary to carry out Air Conditioning ser-
vices or simply A/C services.
Once the vehicle has been accepted from any worksta-
tion, the CoRe server sends the vehicle data and the
data of the required interventions to all other work-
stations and equipment connected to it, in this way
the operators and the equipment are already ready to
work on the vehicle without having to enter again the
data needed to identify the vehicle and/or the custom-
er.
The required interventions are then made available in
a few seconds and are subsequently saved in the cen-
tral memory by the CoRe server to optimize the time
needed for vehicle and customer recognition in any
subsequent appointments, where it will be sufficient
to enter the license number or VIN from any worksta-
tion, to view the whole history of the vehicle, the tech-
nical interventions and to view all the reports of the
equipment used in the previous works.
i
ACS 753 must be configured to access the same
WiFi network to which the CoRe server is connect-
ed (see chapter "WiFi Configuration").
|
1 689 989 612 2020-12-01
5.18.2 Configuration
To configure the CoRe function (only displayed if en-
abled in the Setup Menu), follow this procedure:
1. Call up the Main Menu.
2. Select
.
3. Select
.
4. Select Connected Repair [CoRe]. The display
shows three selection options:
+
Settings: to configure the connection to the CoRe
server. The data to enter is as follows:
$
Host address: is the IP address of the CoRe
server.
$
Host port: is the server port used for the con-
nection, typically the port number is set to
59487 by default, but it is possible to check this
parameter on the CoRe server in the Settings -
Computer Overview section.
$
Password: is the password (Interface password)
set during the installation of the CoRe server.
5. Confirm the entered data with
"
ACS 753 will try to connect to the CoRe server to
check that all parameters entered are correct.
5.18.3

Operation

To use the CoRe function:
+
Select available A/C task: to select and perform
A/C services previously registered at CoRe server
level. After connecting the ACS 753 to the CoRe
server using the settings described above, it is
possible through this item to select one of the
available A/C services and perform it on the de-
sired vehicle. Once the A/C service is selected and
performed, the ACS 753 will send a report to the
CoRe server that will automatically save the result
and all data related to it.
+
Create new A/C task: to create an A/C service
from the ACS 753 and assign an Air Conditioning
Service to one of the active vehicles in the work-
shop. Selecting this item will display the list of
all active vehicles in the workshop and registered
on the CoRe server regardless of whether or not a
specific A/C service has been requested. When the
vehicle is selected, the ACS 753 will send a spe-
cial command to the CoRe server so that the latter
registers that an A/C service is being performed on
the selected vehicle. At the end of the A/C service,
a detailed report will be sent to the CoRe server
that will save it and make it available for displaying
or printing.
.
Robert Bosch GmbH