Technical Data - Scheppach HS110 Original Bedienungsanleitung

• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If the machine is not used for an extended period of
time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Safety Instructions for Handling Batteries
1. Attention: Risk of explosion with improper re-
placement of the batteries. Only replace the bat-
teries with batteries of the same or an equivalent
type. Observe the "Technical data".
2. Batteries must not be charged, reactivated by oth-
er means, taken apart, thrown into fire or short
circuited.
3. Avoid contact with the skin, eyes and mucous
membrane. In case of contact with battery acid,
the affected area must be rinsed immediately with
plenty of clean water. Seek medical advice imme-
diately.
4. If batteries are swallowed or enter the body in
any other way, seek medical advice immediately.
Keep batteries away from children and animals.
5. Remove batteries from the battery compartment if
they are depleted, or if the circular table saw is out
of use for an extended period of time. This avoids
damage that may arise due to batteries leaking.
6. Never expose batteries to extreme conditions by
storing them on radiators or in direct sunlight for
example.
7. Clean the battery and device contacts if neces-
sary before insertion, with a little emery cloth for
example.
8. Ensure correct polarity during insertion.
9. Do not use old and new batteries of different types
together.
Residual Risks
This power tool has been constructed in accord-
ance with the latest technology and the general-
ly recognised safety regulations. Nevertheless,
it is possible that individual residual risks may
occur during operation.
• Electrical hazard if improper electrical connection
cables are used.
34 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• In addition, concealed residual risks may be pres-
ent in spite of all the precautions that have been
taken.
• Residual risks can be minimised by observing the
„Safety instructions" and „Use in accordance with
the designated purpose", as well as the operating
instructions.
• Do not put any unnecessary stresses on the ma-
chine: excessive pressure during sawing will quick-
ly damage the saw blade. This may result in a re-
duction in the performance of the machine, as well
as a reduction in the cutting accuracy.
• Avoid switching the machine on by accident: when
inserting the plug into the socket, the power button
must not be pressed.
• Use the tool which is recommended in this manual.
This will ensure the optimal performance of your
saw.
• Keep your hands away from the working area when
the machine is in operation.
• Before you carry out any adjustments or servicing
work, turn the device off and remove the mains
plug.

7. Technical data

AC motor
Power
Operating mode
Idle speed
Hard metal saw blade
Number of teeth
Riving knife thickness
Min. workpiece dimen-
sions
W x L x H
Table size
Cutting height max. 90°
Cutting height max. 45°
Height adjustment
Tilting saw blade
Suction connection
Weight approx.
Laser class
Laser wavelength
Laser power
Laser module power supply
230 V ~ 50Hz
2000 Watts
S6 40% *
4800 min
-1
ø 254 x ø 30 x 2,8 mm
24
2,5 mm
10 x 50 x 1 mm
546 x 630 mm
87 mm
55 mm
0 - 87 mm
0 - 45°
ø 40 mm
19/21 kg
2
650 nm
≤ 1 mW
2x1,5V; AAA