Scheppach HS110 Original Bedienungsanleitung Seite 31

5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of the
power tool is maintained.
m WARNING
This electric tool generates an electromagnetic field
during operation. This field can impair active or pas-
sive medical implants under certain conditions. In or-
der to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
Safety instructions for table saws
Guarding related warnings
a) Keep guards in place. Guards must be in
working order and be properly mounted.
A guard that is loose, damaged, or is not function-
ing correctly must be repaired or replaced.
b) Always use saw blade guard, riving knife and
for every through–cutting operation.
For through-cutting operations where the saw
blade cuts completely through the thickness of the
workpiece, the guard and other safety devices help
reduce the risk of injury.
c) After completing working procedures where
the removal of the protective cover and/or riv-
ing knife is necessary (e.g. producing folds
and rebating, cutting grooves or cutting with
a turnover), the protective system must be im-
mediately reattached.
The guard helps to reduce the risk of injury.
d) Make sure the saw blade is not contacting the
guard, riving knife or the workpiece before
the switch is turned on.
Inadvertent contact of these items with the saw
blade could cause a hazardous condition.
e) Adjust the riving knife as described in this in-
struction manual. Incorrect spacing, positioning
and alignment can make the riving knife ineffective
in reducing the likelihood of kickback.
f) For the riving knife to work, they must be en-
gaged in the workpiece. The riving knife are
ineffective when cutting workpieces that are too
short to be engaged with the riving knife. Under
these conditions a kickback cannot be prevented
by the riving knife.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
g) Use the appropriate saw blade for the riving
knife. For the riving knife to function properly, the
saw blade diameter must match the appropriate
riving knife and the body of the saw blade must be
thinner than the thickness of the riving knife and
the cutting width of the saw blade must be wider
than the thickness of the riving knife.
Safety information for sawing
a) m DANGER: Do not place your hands and fin-
gers in the sawing area or close to the saw
blade.
A moment of carelessness or a slip could steer
your hand towards the saw blade and result in se-
rious injuries.
b) Only guide the workpiece against the rotation-
al direction of the saw blade or cutting tool.
Guiding the workpiece in the same direction as
the rotational direction of the saw blade above the
table can lead to the workpiece and your hand be-
ing drawn into the saw blade.
c) When performing longitudinal cuts, never use
the mitre stop to guide the workpiece, and
when transverse cutting with the mitre stop
never additionally use the parallel stop for
longitudinal adjustment. Simultaneously guid-
ing the workpiece with the parallel stop and mitre
stop increases the probability that the saw blade
will jam and kickback will result.
d) When performing longitudinal cuts, always
apply the feed force to the workpiece between
the stop rail and the saw blade. Use a push
rod if the distance between the stop rail and
saw blade is less than 150 mm, and a push
block if the distance is less than 50 mm.
This type of working aid ensures that your hands
remain a safe distance from the saw blade.
e) Only use the push rod provided by the man-
ufacturer, or a push rod that has been pro-
duced in accordance with instructions.
The push rod ensures a sufficient distance be-
tween the hand and saw blade.
f) Never use a damaged or partially sawn push
rod.
A damaged push rod may break and lead to your
hand running into the saw blade.
g) Never work "freehand". Always use the paral-
lel stop or the mitre stop to position and guide
the workpiece. "Freehand" means supporting
or guiding the workpiece with the hands, rath-
er than using the parallel stop or mitre stop.
Free-handed sawing leads to incorrect alignment,
jamming and kickback.
h) Never reach around or over a turning saw
blade.
Reaching for a workpiece can lead to accidental
contact with the rotating saw blade.
GB | 31