Scheppach DP16VLS Original Bedienungsanleitung Seite 24

• Never leave the tool before it has come to a
complete standstill. Afterrunning bits can cause
injury.
• Do not use the power tool with a damaged ca-
ble. Do not touch the damaged cable and pull
the mains plug if the cable is damaged while
working. Damaged cables increase the risk of
electric shock.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If the machine is not used for an extended period of
time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Safety instructions for handling batteries
1. Always make sure that the batteries are inserted
with the correct polarity (+ and –), as indicated
on the battery.
2. Do not short-circuit batteries.
3. Do not charge non-rechargeable batteries.
4. Do not overcharge batteries!
5. Do not mix old and new batteries or batteries
of different types or manufacturers! Replace an
entire set of batteries at the same time.
6. Immediately remove used batteries from the
device and dispose of them properly! Do
not dispose batteries with household waste.
Defective or used batteries must be recycled
according to Directive 2006/66 / EC. Give back
batteries and / or the device has been offered to
the collective facilities. About disposal facilities
you can inform by your municipal or city govern-
ment.
7. Do not allow batteries to heat up!
8. Do not weld or solder directly on batteries!
9. Do not dismantle batteries!
24 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
10. Do not allow batteries to deform!
11. Do not throw batteries into fire!
12. Keep batteries out of the reach of children.
13. Do not allow children to replace batteries without
supervision!
14. Do not keep batteries near fire, ovens or other
sources of heat. Do not use batteries in direct
sunlight or store them in vehicles in hot weather.
15. Keep unused batteries in the original packaging
and keep them away from metal objects. Do not
mix unpacked batteries or toss them together!
This can lead to a short-circuit of the battery and
thus damage, burns or even the risk of fire.
16. Remove batteries from the equipment when it
will not be used for an extended period of time,
unless it is for emergencies!
17. NEVER handle batteries that have leaked with-
out appropriate protection. If the leaked fluid
comes into contact with your skin, the skin in this
area should be rinsed off under running water
immediately. Always prevent the fluid from com-
ing into contact with the eyes and mouth. In the
event of contact, please seek immediate medi-
cal attention.
18. Clean the battery contacts and corresponding
contacts in the device prior to inserting the bat-
teries.
Residual risks
The machine has been built according to the
state of the art and the recognised technical
safety requirements. However, individual residu-
al risks can arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Use the tool that is recommended in this manual.
In doing so, your drill press provides optimal per-
formance.
• Hands may never enter the processing zone when
the machine is in operation.
• Release the handle button and switch off the ma-
chine prior to any operations.