Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until "ADJUST
TIME" is displayed;
3. Press the OK button (B4). The hours flash on the display;
4. Press the ▽ and △ buttons (B5 and B6) to change the
hours;
5. Press the OK button (B4) to confirm. The minutes flash on
the display;
6. Press the ▽ and △ buttons (B5 and B6) to change the
minutes;
7. Press the OK button (B4) to confirm;
8. Press the P / ESC button (B7) to exit the settings menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note:
To enable this function, the time must be set correctly.
To enable Auto-on, proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until "AUTO-
START" is displayed;
3. Press the OK button (B4). "ENABLE?" is displayed;
4. Press the OK button (B4). The hours flash on the display;
5. Press the ▽ and △ buttons (B5 and B6) to choose the
hours;
6. Press the OK button (B4) to confirm. The minutes flash on
the display;
7. Press the ▽ and △ buttons (B5 and B6) to change the
minutes;
8. Press the OK button (B4) to confirm. "ENABLED" appears
under "AUTO-START".
9. Press the P/ ESC button (B7) to exit the menu.
To disable the function:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until "AUTO-
START" is displayed;
3. Press the OK button (B4). "DISABLE?" is displayed;
4. Press the OK button (B4) to confirm;
5. Press the P/ ESC button (B7) to exit the menu. "DISABLED" is
displayed.
Auto-off (Standby)
The appliance is set by default to go off if not used for two
hours.
The time can be changed so that the appliance switches off after
15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-off, proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until "AUTO-OFF"
is displayed;
3. Press the OK button (B4);
4. Press the ▽ and △ buttons (B5 and B6) until the required
time (15 or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button (B4) to confirm;
6. Press the P/ ESC button (B7) to exit the menu.
Auto-off is programmed.
Setting the temperature
To modify the temperature of the water used to make the coffee,
proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until "SET TEMPE-
RATURE" is displayed;
3. Press the OK button (B4);
4. Press the ▽ and △ buttons (B5 and B6) until the required
temperature is displayed (l = low, llll = high);
5. Press the OK button (B4) to confirm;
6. Press the P/ ESC button (B7) to exit the menu.
Setting water hardness
The operating period can be extended if required, making desca-
ling less frequent by programming the machine on the basis of
the real lime content in the water used.
Proceed as follows:
•
Remove the " Total Hardness Test" strip (attached to page 2)
from its packaging then dip it fully in the water for a few
seconds.
Remove and wait about 30 seconds (until it changes colour
and forms red squares).
•
Turn the appliance on by pressing the ON/OFF/standby but-
ton (A7).
•
Press the P / ESC button (B7) to enter the menu and then the
▽ and △ buttons (B5 and B6) until "WATER HARDNESS" is
displayed.
•
Press the OK button (B4);
Press the ▽ and △ buttons (B5 and B6) until the number
•
coincides with the number of red squares on the test strip
(for example, if there are 3 red squares on the test strip, se-
lect the message "WATER HARDNESS lll" .
•
Press the OK button (B4) to confirm.
The coffee machine is now programmed to provide the de-
scale warning when actually necessary.
18
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
