Herunterladen Inhalt Inhalt Diese Seite drucken

Kickback And Corresponding Safety Instructions - Parkside PWS 230 D4 Originalbetriebsanleitung

Winkelschleifer
Vorschau ausblenden Andere Handbücher für PWS 230 D4:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

j) Hold the power tool only by the insulated
handles when you are carrying out work in
which the accessory tool may come into con-
tact with concealed power cables or the
tool's own power cord. Contact with a live ca-
ble can also make metal parts of the appliance
live and could result in an electric shock .
k) Keep the power cord away from any rotating
accessories. If you lose control of the appli-
ance, the cord may get caught or cut and your
hand or arm could get caught in the rotating
accessory tool .
l) Never put the power tool down until the ac-
cessory tool being used has come to a com-
plete standstill. The rotating accessory tool can
come into contact with the surface and cause
you to lose control of the power tool .
m) Do not leave the power tool running whilst
carrying it. Accidental contact between your
clothing and the rotating accessory tool could
lead to physical injury .
n) Clean the ventilation slits of your power tool
regularly. The engine fan draws dust into the
housing and a strong accumulation of metal
dust can cause electrical hazards .
o) Never use the power tool in the vicinity of in-
flammable materials. Sparks can ignite these
materials .
p) Do not use any accessory tools which require
liquid coolant. The use of water or other liquid
coolants may lead to electric shock .
Kickback and corresponding safety
instructions
Kickback is a sudden reaction caused when a ro-
tating accessory tool, e .g . grinding disc, grinding
plate, wire brush, etc ., catches or jams . Catching or
jamming leads to an abrupt stop of the rotating ac-
cessory tool . If this happens, an uncontrolled pow-
er tool turns rapidly against the direction of rotation
of the accessory tool caught in the blockage .
6 
GB │ IE │ NI │ CY
If, for example, a grinding disc catches or jams in a
workpiece, the edge of the grinding disc projecting
into the workpiece can get caught and break off
the grinding disc or cause a kickback . The grinding
disc can then fly in the direction of the operator or
away from him, depending on the direction of rota-
tion of the disc at the blockage . This can also break
grinding discs .
A kickback is caused by incorrect use or misuse of
the power tool . This can be avoided by taking
proper precautions as described below .
a) Hold the power tool firmly in both hands and
position your body and arms so they can ab-
sorb the force of a kickback. Always use the
additional handle, if available, so that you
have the maximum possible control over the
kickback force or reaction forces at full
speed. By taking adequate precautions, the op-
erator can stay in control of the kickback and
reaction torques .
b) Never hold your hand close to a rotating ac-
cessory tool. The accessory tool could hit your
hand in the event of a kickback .
c) Avoid having any part of your body in the
region in which the power tool is likely to
move in event of a kickback. The kickback will
force the power tool in the opposite direction to
the direction of rotation of the grinding disc at
the blockage .
d) Take special care when working near cor-
ners, sharp edges, etc. Avoid allowing the
accessory tool to bounce back from the work-
piece or jam. The rotating accessory tool is
more likely to jam in corners or sharp edges or
if it rebounds off them . This can cause a loss of
control or kickback .
e) Do not use chains or toothed saw blades.
Such accessories often cause a kickback or loss
of control over the power tool .
PWS 230 D4

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis