Seite 1
DMA 35 Portable Density/Specific Gravity/ Concentration Meter ::: Unique Density & Concentration Meters Instruction Manual | Betriebsanleitung...
Seite 3
DMA 35 Portable Density Meter From Firmware Version V1.79 Instruction Manual C96IB01...
Seite 4
Nor is any liability assumed for damages resulting from the use of the information contained in this instruction manual. Anton Paar GmbH does not make a commitment to update the information in this manual. Specifications are subject to change without notice.
1 About the Instruction Manual ................8 2 Safety Instructions ..................10 3 Measuring Principle ..................12 4 DMA 35 - an Overview ..................13 5 Checking the Supplied Parts ................. 14 6 Description of the Instrument ................ 17 Front View ....................17 Rear View ....................
Seite 6
9.1.3 Importing Custom Functions .............33 Selecting Measuring Methods ..............34 9.2.1 Entering a New Method ..............34 9.2.2 Entering Method Lists ...............35 9.2.3 Editing a Method ................37 9.2.4 Deleting a Method ................37 9.2.5 Deleting all Methods .................37 9.2.6 Selecting a Method ................38 Assigning a Sample ID ................38 9.3.1 Entering the Sample ID ..............38 9.3.2 Entering Sample ID Lists ..............39...
Seite 7
10 Cleaning and Storing the Instrument ............54 10.1 Cleaning the Measuring Cell ..............54 10.2 Cleaning the Filling Pump ................ 54 10.3 Cleaning the Pump Housing ..............54 10.4 Cleaning the Housing and Display ............55 10.5 Storing the Instrument ................55 11 Maintenance ....................
About the Instruction Manual This instruction manual informs you about the installation and the safe handling and use of the product. Pay special attention to the safety instructions and warnings in the manual and on the product. The instruction manual is a part of the product. Keep this instruction manual for the complete working life of the product and make sure it is easily accessible to all people involved with the product.
Seite 9
Typographical conventions The following typographical conventions are used in this instruction manual: Convention Description <key> The names of keys and buttons are written inside angle brackets. "Menu Level 1 > Menu Level 2" Menu paths are written in bold, inside straight quotation marks.
• Only use DMA 35 for the purpose described in this instruction manual. Anton Paar GmbH is not liable for damages caused by incorrect use of DMA 35. Installation and use •...
Seite 11
The intrinsically safe DMA 35 Ex and DMA 35 Ex Petrol (types DMA 35 Version 3 Ex and DMA 35 Version 3 Ex Petrol) can be used according to ATEX marking II 2 G Ex ib IIC T4. All instructions given in the certificate of conformity have to be followed (see Appendix D).
Do not leave sample/rinsing containers uncovered. Clean all spillages immediately. • Make sure that the setup location is sufficiently ventilated. The environment of DMA 35 must be kept free of flammable gases and vapors. • Supply a fire extinguisher. Measuring Principle Definition of density The density ρ...
DMA 35 is operated via seven keys. 1024 measuring data including date, time and sample ID can be stored in the memory of the DMA 35 density meter and can be recalled, exported to a PC or printed later. The transfer of the stored measuring data to a printer or PC is done wireless using an infrared interface (IrDA).
Checking the Supplied Parts DMA 35 was tested and packed carefully before shipment. However, damage may occur during transport. Keep the packaging material (box, foam piece) for possible returns and further questions from the transport company or insurance company. Check the delivery for completion by comparing the supplied parts to those given in Table 5.1.
Seite 15
Article Description Mat. No. DMA 35 portable density meter or 84138 or DMA 35 Tag&Log portable density 87448 meter or DMA 35 Ex portable density meter or 87450 or DMA 35 Ex Petrol portable density 87451 meter Instruction Manual English/German...
Seite 16
Black laundry tag 30 mm R/W 88444 White PVC sticker disc tag 30 mm R/W 88445 White PVC sticker disc tag 30 mm R 92414 Carrying case for DMA 35 88506 Custom function for DMA 35 88974 DKD calibration DMA 35 88153...
Front view of DMA 35 ... Built-in pump ... Screw plug ... Measuring cell ... Softkeys ... Operating keys ... RFID interface (only for DMA 35 Tag&Log, DMA 35 Ex and DMA 35 Ex Petrol) ... Graphical, monochrome LC display C96IB01...
Seite 18
Fig. 6 - 2 Top view of DMA 35 ... Built-in pump ... Fixing screw of the pump lock ... Pump lock ... Infrared interface (IrDA) Keys at the front side For switching the instrument on and off. For deleting measuring data, entries and characters during an entry.
Rear view of DMA 35 ... Data storage key ... Type plate with serial number ... Registration number and ATEX marking (only for DMA 35 Ex and DMA 35 Ex Petrol) ... Custom functions (optional) ... Mark for the correct battery insertion ...
... Symbol for battery charge status ... Warning sign ... Measuring value ... Sample temperature °C/°F ... Softkey configuration ... Sample ID 10 ... Method 11 ... Custom offset 12 ... Measuring unit Only for DMA 35 versions with RFID interface C96IB01...
Seite 21
Symbols on the display The infrared data transfer symbol is shown on the information header when data is imported or exported via the IrDA interface. The RFID symbol is shown on the information header when it is possible to allocate an RFID tag to a method or sample ID and when an RFID tag is read while the instrument displays the main screen.
Operating the DMA 35 Connecting the Filling Tube • Screw in the filling tube by hand until you feel some resistance against turning. Do not use any tools for screwing in the filling tube. Fig. 7 - 1 Connecting the filling tube Attaching the Syringe Adapter Remove the screw plug at the side of the instrument.
To switch the instrument off, press the key until "Power Off" is displayed. If the instrument is in the energy saving mode (see Chapter 8.4), DMA 35 switches automatically off after 3, 5 or 10 minutes inactivity (depending on the setting).
Your settings are saved and the measuring results are shown in the selected units. Sound Settings When sound is enabled, DMA 35 beeps when it is switched on and off and when a key is pressed. When sound is disabled, the instrument only beeps when it is switched on and off.
Backlight The LC display and the oscillator are equipped with a backlight. The backlight ensures that even under bad lighting conditions the measuring results and menu options are easily readable. The backlight of the oscillator enables you to observe the filling process.
Allocation of the Softkey Function On the front side of DMA 35 are two softkeys. When the instrument displays the main screen, the left softkey always takes you to the main menu. The right softkey can be allocated with one out of three predefined functions. The allocated function is only available in the main screen.
Enter the password again and press <Save>. The password has now been saved. Keep your password information safe. To change or delete the password Press <Menu> and select "Setup". Enter your password. Select "Set Password". Enter the current password and press <OK>. If you want to change the password, enter the new password.
If your PC has no IrDA interface, install the IrDA USB adapter on your PC. Hold the IrDA interface of DMA 35 to the IrDA interface of your PC to establish communication between the two instruments.
Performing a Measurement General instructions for measuring WARNING Handling samples with temperatures of more than 70 °C bears the danger of heavy burns. Make sure you wear protective clothes or ensure alternative protection from burns when handling high temperature samples. NOTICE Before performing a measurement, make sure that the wetted parts are resistant to the sample (see Chapter 15).
For measuring your samples you can choose between a number of predefined measuring units or you can import custom functions into the instrument and select one of them as the measuring unit. Contact your Anton Paar representative to obtain a custom function from Anton Paar.
9.1.1 Categories of Measuring Units Meas. Options Description units Density Density Density at the displayed measuring temperature in g/cm or kg/m Density @ xx °C: Density at the chosen reference α (g/cm temperature in g/cm or kg/m . The temperature influence is compensated by the set temperature coefficient α.
For determining degree Baumé there are two different calculation methods depending on whether the density is above or below the density of water. Depending on the density of the measured liquid, DMA 35 automatically switches between the two calculation methods. H2SO4 H2SO4 % w/w Concentration of sulfuric acid or battery acid in % by weight.
If your PC has no IrDA interface, install the IrDA USB adapter on your PC. Press <Menu> and select "Setup > Import / Export > Receive from PC". Hold the IrDA interface of DMA 35 to the IrDA interface of your PC to establish communication between the two instruments.
You can define and name up to 20 different measuring methods. To see how many of the 20 storage places are still available, go to the menu "Device Information" (see Chapter 11.3). If you own several DMA 35 instruments, you can import the same method list to all instruments. 9.2.1 Entering a New Method Select the preferred measuring parameter (see Chapter 9.1) and, if necessary,...
If you plan to set up or edit large method lists, you can do so conveniently on the PC and then import the list to DMA 35. If you own several DMA 35 instruments, you can import the same method list to all instruments to get several identical instruments.
Seite 36
To enter method lists If your PC has no IrDA interface, install the IrDA USB adapter to your PC. Hold the IrDA interface of DMA 35 to the IrDA interface of your PC to establish communication between the two instruments.
Save your changes. Press <Menu> and select "Setup > Import / Export > Receive from PC". Hold the IrDA interface of DMA 35 to the IrDA interface of your PC to again establish communication between the two instruments. On your PC, right click on the file you want to transmit and select "Send to > A nearby computer".
9.2.6 Selecting a Method Press <Menu> and choose "Methods > Select Method". All stored methods are displayed. Select the preferred method and press <OK>. The name of the measuring method is displayed on the main screen and the following measurements are performed according to the selected method. Assigning a Sample ID You can assign different sample IDs to samples.
If you plan to set up or edit large sample ID lists, you can do so conveniently on the PC and then import the list to DMA 35. If you own several DMA 35 instruments, you can import the same sample ID list to all instruments to get several identical instruments.
Seite 40
To enter a sample ID list If your PC has no IrDA interface, install the IrDA USB adapter on your PC. Hold the IrDA interface of DMA 35 to the IrDA interface of the PC to establish communication between the two instruments.
9.3.3 Changing the Sample ID Press <Menu> and select "Sample-ID > Edit ID". Select the ID you want to change and press <OK>. For changing the sample ID, see Chapter 9.3.3; for allocating an RFID tag, see Chapter 9.5.2; for programming an RFID tag, see Chapter 9.5.3. 9.3.4 Deleting a Sample ID Press <Menu>...
ID is automatically used for the following measurements. 9.5.1 Preconditions for Using RFID The reading range of the RFID receiver integrated in DMA 35 is about 2 cm. The RFID tag has to be situated within this area to enable data exchange with DMA 35.
Allocation of an RFID tag is done by reading the unique identification number of the tag via the RFID interface of DMA 35 and by allocating this identification number to a method and/or sample ID on the instrument. Allocation is done exclusively on the instrument and no programming of the RFID tag is done.
Besides allocation of RFID tags to sample IDs and/or methods on the instrument (see Chapter 9.5.2), DMA 35 versions with RFID interface provide the option to write the sample ID and/or method to an RFID tag. Using this programming feature makes you independent regarding the amount of sample IDs and methods used as no sample ID list or method list has to be stored permanently on the instrument.
Reading the RFID information helps you to identify an RFID tag in case the tags got mixed up, or you want to check if the tag was programmed correctly, or you want to check the compatibility of a tag type with DMA 35 versions with RFID interface. The RFID information states details about: •...
Hold the allocated or programmed RFID tag to the RFID interface of the instrument. The method and/or sample ID allocated to or stored on the RFID tag will automatically be used for the following measurements. 9.5.7 Application Examples for RFID RFID tags can be attached on the outside of tank farms, for example.
Filling Sample Depending on the viscosity of the sample, you can fill the measuring cell using the filling tube or the plastic syringe. When filling highly viscous samples, we recommend using the plastic syringe. 9.6.1 Filling Using the Filling Tube Press down the pump lever as far as it will go (see Fig.
9.6.2 Filling with the Plastic Syringe NOTICE Do not remove the pump when filling with the plastic syringe. Otherwise, the system is leaky. Fill the plastic syringe with the sample. Fill the measuring cell through the Luer adapter using the plastic syringe. Fig.
Switch on the printer with the IrDA interface. Press the <Print> key when the measured value appears on the display. Hold the IrDA interface of DMA 35 to the IrDA interface of the printer to establish communication between the printer and density meter.
Accessing Saved Measuring Data You can save up to 1024 measuring data directly in the instrument’s memory. If the memory contains 1024 saved values, further values will overwrite the oldest saved values. Each saved value is given a consecutive 4-digit number. Using this number you can see whether the instrument has overwritten old entries.
Select the measured value required for export using the arrow keys. Press <Export>. Hold the IrDA interface of DMA 35 to the IrDA interface of the PC to establish communication between the two instruments. Select <Export Selected> to export the selected measured value to the PC.
Option 2: If your PC has no IrDA interface, install the IrDA USB adapter on your PC. Hold the IrDA interface of DMA 35 to the IrDA interface of the PC to establish communication between the two instruments. Press <Menu> and select "Setup > Import / Export > Send to PC >...
All measuring data are printed. 9.11 Deleting the Saved Measuring Data To delete the last measured value Press <Menu> and select "Measuring Data". Select a measured value and press Select <Delete Last> and press <OK>. Press <Delete> when asked if you really want to delete the last measured value. The last measured value is removed from the list.
Empty the measuring cell by pressing the pump lever. 10.3 Cleaning the Pump Housing DMA 35 is completely sealed against the outside and the pump. Therefore, you can rinse the pump housing with running tap water if the housing is dirty.
Empty the measuring cell by pressing the pump lever. Open the pump lock and remove the pump. Hold the pump housing under running water and rinse it thoroughly. Insert the pump and close the pump lock. Empty the measuring cell by pressing the pump lever. 10.4 Cleaning the Housing and Display To clean the housing and display, use a soft cloth dipped in ethanol or warm water.
Only use batteries of the same type and with the same level of battery charge. • For DMA 35 instruments with ATEX marking (DMA 35 Ex and DMA 35 Ex Petrol), only use the permitted alkaline battery type EN91 (LR06, AA) from Energizer Industrial.
Seite 57
Empty the measuring cell by pressing the pump lever. Open the pump lock and remove the pump. Fig. 11 - 1 Removing the pump Screw out the screw of the pump lock using an Allen key size 2.5 and remove the screw.
Seite 58
Fig. 11 - 3 Removing the pump lock Use a coin to open the battery cover by turning. Fig. 11 - 4 Opening the battery cover Remove the flat batteries by turning the instrument upside down. Insert the new batteries. The picture on the back of the instrument shows the correct positioning of the batteries.
If your PC has no IrDA interface, install the IrDA USB adapter on your PC. Hold the IrDA interface of DMA 35 to the IrDA interface of the PC to establish communication between the two instruments. Press <Menu> and select "Setup > Import / Export > Receive from PC".
Press <Menu> and select "Setup > Import / Export > Send to PC > Device Information". Hold the IrDA interface of DMA 35 to the IrDA interface of the PC to establish communication between the two instruments. A dialog window appears on the PC asking if you want to accept the file.
Press <Menu> and select "Setup > Import / Export > Send to PC > Adjustment". Hold the IrDA interface of DMA 35 to the IrDA interface of the PC to establish communication between the two instruments. A dialog window appears on the PC asking you to accept the file transfer.
12 Readjustment To ensure accurate results it is necessary to clean the measuring cell before and after each measurement series. If the measuring cell is not sufficiently cleaned, residue can form in the measuring cell. This can be noticed if the density values for deionized water begin to deviate.
12.3 Custom Adjustment You can also use any other reference liquid with a known density at 20 °C and known temperature coefficient for your readjustment. We recommend using the customer adjustment e.g. if you measure only liquids in a specific density range (e.g. high density) and want to yield more accurate results in this range.
12.5 Restoring to Factory Adjustment If you want to undo all your adjustments you can restore the factory adjustment. Press <Menu> and select "Adjustment > Factory Adjustment". The display shows: "Are you sure that you want to reset to factory adjustment?" Press <OK>...
Error 01 The temperature is invalid. Error 02 The period is invalid. Error 03 DMA 35 has no adjustment data. Error 04 Calculation error. NOTICE If the error messages "Error 01" to "Error 04" occur, send in your instrument for service.
160 x 240 pixel Data memory: 1024 measuring data Interfaces: DMA 35: IrOBEX/IrLPT DMA 35 Tag&Log, DMA 35 Ex and DMA 35 Ex Petrol: IrOBEX/IrLPT, RFID Power supply: Battery type: Alkaline battery 1.5V, type EN91 (LR06, AA) from Energizer Industrial Battery life: >...
Housing for DMA 35 Ex Petrol PP (Polypropylene) Faradex MS002 Housing for DMA 35, DMA 35 Tag&Log and DMA 35 Ex PVDF (Polyvinylidene fluoride) Connection block, bolt Viton O-ring for DMA 35, DMA 35 Tag&Log and DMA 35 Ex C96IB01...
Appendix B: Measuring Unit Details Measuring unit Minimum Maximum Unit Format Offset format 0.0000 3.0000 g/cm³ n.nnnn 0.0nnn Density 0000.0 3000.0 kg/m³ nnnn.n 00nn.n 0.0000 3.0000 g/cm³ n.nnnn 0.0nnn Density @ xx °C 0000.0 3000.0 kg/m³ nnnn.n 00nn.n Specific Gravity SG 0.0000 3.0000 n.nnnn...
Seite 70
Measuring unit Minimum Maximum Unit Format Offset format 0.5000 1.5000 g/cm³ nnnn.n 0.0nnn API Density A 0500.0 1500.0 kg/m³ n.nnnn 00nn.n 0.5000 1.5000 g/cm³ nnnn.n 0.0nnn API Density B 0500.0 1500.0 kg/m³ n.nnnn 00nn.n 0.5000 1.5000 g/cm³ nnnn.n 0.0nnn API Density D 0500.0 1500.0 kg/m³...
Seite 71
ρ ρ Measuring unit [°C] [°C] valid valid [g/cm [g/cm [°C] [°C] H2SO4 % w/w H2SO4 @ 20 °C Alcohol % v/v @ 20 °C Alcohol % w/w Alcohol US @ 60 °F API Gravity A API Gravity B API Gravity D API SG A API SG B API SG D...
Appendix F: Firmware Versions Firmware Release Document Comments version date number V1.54 10.04.2009 C96IB01A First released version. V1.57 05.05.2009 C96IB01A 10 programmable custom functions. V1.78 19.10.2009 C96IB01B • New start screen • Setup menu "Measurement Mode" • Extended RFID functionality (programming RFID tags, reading RFID information, erasing RFID tags)
Appendix G: Menu Tree Measuring Data Export Export All Export Selected Print All Print Selected Sample-ID Select ID Enter new ID Edit ID Send ID to RFID Methods Select Method Enter new Method Edit Method Send Method to RFID Measuring Units Density Density Density @ xx °C...
Seite 80
On; Auto; Off Energy Saving Off; 3 min; 5 min; 10 Beep On; Off Units Density: g/cm3; kg/m3 Temperature: °C; °F RFID Information RFID Erase RFID Language English Deutsch Device Information Only for DMA 35 versions with RFID interface C96IB01...
Seite 81
DMA 35 Tragbares Dichtemessgerät Ab Firmwareversion V1.79 Betriebsanleitung C96IB01...
Seite 82
Auslassungen in diesem Dokument. Außerdem wird keinerlei Haftung übernommen für Schäden, die sich durch die im Dokument enthaltene Information ergeben. Anton Paar GmbH behält sich inhaltliche Änderungen vor. Dies gilt auch für Änderungen des Lieferumfangs in Form, Ausstattung und Technik.
Seite 83
Inhaltsverzeichnis 1 Zur Betriebsanleitung ..................86 2 Sicherheitshinweise ..................88 3 Messprinzip ..................... 91 4 DMA 35 - ein Überblick ................... 92 5 Gelieferte Teile prüfen ..................93 6 Beschreibung des Gerätes ................96 Vorderansicht ................... 96 Rückansicht ..................... 98 Display .....................
Zur Betriebsanleitung Diese Betriebsanleitung informiert Sie über die Installation, die sichere Handhabung und den sicheren Betrieb des Produktes. Beachten Sie besonders die Sicherheitshinweise und Warnungen in der Anleitung und auf dem Produkt. Die Betriebsanleitung ist ein Teil des Produktes. Bewahren Sie die Betriebsanleitung während der gesamten Lebensdauer des Produktes auf.
Seite 87
Typografische Standards In dieser Betriebsanleitung werden folgende typografische Standards angewendet: Standard Beschreibung <Taste> Die Namen von Tasten und Schaltflächen werden innerhalb von spitzen Klammern geschrieben. "Menüebene 1 > Menüebene 2" Die Menüpfade werden fett, innerhalb von geraden Anführungszeichen geschrieben. Die Menüebenen werden mit einer schließenden spitzen Klammer verbunden.
Schulung über den sicheren und ordnungsgemäßen Gebrauch des Gerätes erhalten. • Im Falle einer Beschädigung oder Störung dürfen Sie das DMA 35 nicht weiter verwenden. Bringen Sie das Gerät nicht in Betriebszustände, die zur Beschädigung von Sachen und/oder zur Gefährdung von Personen führen können.
Seite 89
• Das DMA 35 darf nicht unter 0 °C abgekühlt werden, solange sich Wasser in der Messzelle oder in der Pumpe befindet (gefrierendes Wasser sprengt die Messzelle). Betrieb in explosionsgefährdeten Bereichen • In explosionsgefährdeten Bereichen dürfen Sie nur Geräte in Betrieb nehmen, die mit einem Ex-Typenschild nach ATEX gekennzeichnet sind.
Seite 90
Schütten Sie Proben/Spülflüssigkeiten nicht aus, und lassen Sie sie nicht unabgedeckt stehen. Entfernen Sie verschüttete Proben/Spülflüssigkeiten sofort. • Sorgen Sie für eine ausreichende Belüftung des Betriebsortes. Die Umgebung des DMA 35 muss frei von brennbaren Gasen und Dämpfen gehalten werden. • Stellen Sie eine Feuerlöscheinrichtung bereit. C96IB01...
Messprinzip Definition von Dichte ρ Die Dichte einer Probe ist definiert als Masse der Probe dividiert durch Volumen der Probe: ρ ---- - Die Dichte ist eine temperaturabhängige Messgröße. Das Biegeschwingerprinzip Die Probe wird in ein U-förmiges Rohr aus Borosilikatglas eingefüllt, welches über einen Elektromagneten in seiner Resonanzfrequenz zur Schwingung erregt wird.
II 2 G Ex ib IIC T4) sind für den Betrieb in explosionsgefährdeten Bereichen zulässig. Das DMA 35 Ex ist ideal für Anwendungen in der chemischen Industrie sowie für die Messung von Batteriesäure. Das DMA 35 Ex Petrol ist mit einem Spezialgehäuse für die petrochemische Industrie ausgestattet, welches gegen Treibstoffe und ähnliche organische Lösungen beständig ist.
Gelieferte Teile prüfen Das DMA 35 wurde vor der Auslieferung werkseitig geprüft und sorgfältig verpackt. Trotzdem kann das Gerät während des Transportes beschädigt werden. Verwahren Sie das Verpackungsmaterial (Karton, Schaumteile) für etwaige Transporte oder Rückfragen der Transportfirma oder Versicherung. Um die Lieferung auf Vollständigkeit zu überprüfen, vergleichen Sie die gelieferten Teile mit den in Tabelle 5.1 aufgeführten.
Seite 94
DMA 35 Tag&Log Portables 87448 Dichtemessgerät oder oder DMA 35 Ex Portables 87450 Dichtemessgerät oder oder DMA 35 Ex Petrol Portables 87451 Dichtemessgerät Betriebsanleitung Englisch/Deutsch 88155 Saugrohr (Standard 180 mm) 68527 Luerbuchse (für Spritzenbefüllung) 64792 Einmalspritzen 2 mL 58802 Inbusschlüssel gewinkelt 2,5 mm...
Seite 95
Schwarzer Laundry-Tag 30 mm R 92413 Schwarzer Laundry-Tag 30 mm R/W 88444 DKD-Kalibrierung DMA 35 88153 Drucker CMP-10-E5 RS232C/IrDA 87817 IrDA-USB-Adapter LCS-8141 88085 Kundenfunktion für DMA 35 88974 Kunststoffkoffer für DMA 35 88506 Saugrohr 600 mm 78503 Set Handschlaufe Für DMA 35 92416 C96IB01...
Beschreibung des Gerätes Vorderansicht Abb. 6 - 1 Vorderansicht des DMA 35 ... Einsaugpumpe ... Verschlussschraube ... Messzelle ... Funktionstasten ... Bedientasten ... RFID-Schnittstelle (nur bei DMA 35 Tag&Log, DMA 35 Ex und DMA 35 Ex Petrol) ... Grafisches, monochromes LC-Display C96IB01...
Seite 97
Abb. 6 - 2 Ansicht des DMA 35 von oben ... Einsaugpumpe ... Fixierschraube der Pumpenverriegelung ... Pumpenverriegelung ... Infrarot-Schnittstelle (IrDA) Tasten an der Vorderseite Zum Ein- und Ausschalten des Geräts. Zum Löschen von Messdaten, Eingaben und Zeichen während der Eingabe.
Rückansicht Abb. 6 - 3 Rückansicht des DMA 35 ... Speichertaste ... Typenschild mit Seriennummer ... Zulassungsnummer und ATEX-Kennzeichnung (nur bei DMA 35 Ex und DMA 35 Ex Petrol) ... Kundenfunktionen (optional) ... Kennzeichnung der Batterieeinschubrichtung ... Kalibriernummer (optional) Taste an der Rückseite Zum Starten und Speichern einer Messung.
... Symbol für Ladezustand der Batterien ... Warnzeichen (für Details zur Warnung <Info> Taste drücken) ... Messwert ... Probentemperatur °C/°F ... Funktionstastenbelegung ... Proben-ID 10 ... Methode 11 ... Kundenoffset 12 ... Messgröße Nur für DMA 35-Versionen mit RFID-Schnittstelle C96IB01...
Seite 100
Symbole am Display Das Symbol für Infrarot-Datenübertragung wird in der Informationsleiste angezeigt, wenn Daten über die IrDA-Schnittstelle importiert oder exportiert werden. Das RFID-Symbol wird in der Informationsleiste angezeigt, wenn es möglich ist, einen RFID-Tag zu einer Methode oder Proben-ID zuzuordnen und wenn in der Hauptansicht ein RFID-Tag eingelesen wird.
Gerät in Betrieb nehmen Saugrohr anschließen • Schrauben Sie das Saugrohr in die Anschlusstülle so weit ein, bis Sie einen Widerstand gegen die Schraubbewegung verspüren. Verwenden Sie zum Einschrauben des Saugrohres kein Werkzeug. Abb. 7 - 1 Saugrohr anschließen Spritzenadapter anschließen Entfernen Sie die seitliche Verschlusstülle.
Gerät einschalten • Drücken Sie zum Einschalten des Gerätes die Taste. Nach der Begrüßungsanzeige wechselt das DMA 35 sofort in die Hauptansicht (Messmodus). Sie können mit dem Messvorgang beginnen. Gerät ausschalten • Drücken Sie zum Ausschalten des Gerätes die Taste solange, bis auf dem Display "Ausschalten"...
Ihre Einstellungen werden übernommen und die Messwerte in der jeweils gewählten Einheit angezeigt. Toneinstellung Bei eingeschaltetem Ton gibt das DMA 35 beim Ein- und Ausschalten sowie bei jedem Tastendruck einen Ton aus. Bei ausgeschaltetem Ton gibt das Gerät nur beim Ein- und Ausschalten einen Ton aus.
Hintergrundbeleuchtung Das LC-Display und der Schwinger sind mit einer Hintergrundbeleuchtung ausgestattet. Die Hintergrundbeleuchtung des Displays ermöglicht eine gute Sichtbarkeit der Messergebnisse und Menüfunktionen auch unter schlechten Lichtbedingungen. Die Hintergrundbeleuchtung des Schwingers ermöglicht Ihnen das genaue Beobachten des Probenfüllprozesses. Sie können zwischen "Auto", "Aus" und "Ein" wählen. Auto Die Hintergrundbeleuchtung schaltet sich automatisch bei jedem Tastendruck ein.
Belegung der Funktionstaste Auf der Vorderseite des DMA 35 befinden sich zwei Funktionstasten, welche mit unterschiedlichen Funktionen belegt sind. Während die linke Funktionstaste Sie in der Hauptansicht stets zum Hauptmenü führt, können Sie die rechte Funktionstaste nach eigenem Ermessen mit einer der vordefinierten Funktionen belegen. Diese Belegung ist nur in der Hauptansicht verfügbar.
Passwortschutz Sie können Ihr Gerät nach Wunsch mit einem Passwort belegen. Bei aktiviertem Passwortschutz ist für Änderungen der Einstellungen, Durchführen einer Justierung und Auswahl von Messgrößen eine Passworteingabe erforderlich. Für die Durchführung von Messungen und das Anlegen, Ändern oder Löschen von Messmethoden oder Proben-IDs ist keine Passworteingabe erforderlich.
Datums- und Uhrzeiteinstellung Die Informationsleiste zeigt während des Betriebs das Datum und die Uhrzeit. Die Einstellungen müssen bei Inbetriebnahme des Geräts einmalig vorgenommen werden. Datum und Uhrzeit einstellen Drücken Sie <Menü> und wählen Sie "Einstellungen > Datum und Zeit > Datum und Zeit".
Wenn Ihr PC über keine IrDA-Schnittstelle verfügt, installieren Sie den IrDA- USB-Adapter auf Ihrem PC. Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Drücken Sie <Menü> und wählen Sie "Einstellungen > Import / Export > Zum PC senden >...
Messung durchführen Allgemeine Hinweise zur Messung WARNUNG Das Hantieren mit Proben, deren Temperatur 70 °C übersteigt, birgt die Gefahr von schweren Verbrennungen. Tragen Sie beim Hantieren mit heißen Proben Schutzkleidung oder stellen Sie den Schutz vor Verbrennungen anderweitig sicher. ACHTUNG Stellen Sie vor der Messung der Probe die Beständigkeit der probenberührenden Teile sicher (siehe Kapitel 15).
Für die Messung Ihrer Probe können Sie zwischen verschiedenen vordefinierten Messgrößen wählen oder selbst eine Kundenfunktion in das Gerät importieren und als Messgröße auswählen. Kontaktieren Sie Ihren Anton-Paar-Vertreter, um eine Kundenfunktion von Anton Paar zu erhalten. Sämtliche Messgrößen werden von der Dichte der Probe bei Messtemperatur abgeleitet.
9.1.1 Arten von Messgrößen Mess- Auswahl- Erläuterung größen möglichkeiten Dichte Dichte Dichte in g/cm oder kg/m bei der angezeigten Messtemperatur. Dichte @ xx °C: Dichte in g/cm oder kg/m bei der gewählten α (g/cm Referenztemperatur. Der Temperatureinfluss wird durch den einzustellenden Temperaturkoeffizienten α...
Seite 112
Temperaturkoeffizienten α (g/ /K) kompensiert. Für °Baumé existieren zwei unterschiedliche Berechnungsmethoden für Dichtegrade, die über oder unter jenem von Wasser liegen. Im DMA 35 ist eine automatische Umschaltung zwischen den beiden Berechnungsmethoden je nach Dichtegrad der gemessenen Flüssigkeit implementiert. H2SO4 H2SO4 % w/w Schwefelsäure- bzw.
Drücken Sie <Menü> und wählen Sie "Einstellungen > Import / Export > Vom PC empfangen". Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Klicken Sie am PC mit der rechten Maustaste auf die Datei, die Sie senden möchten, und wählen Sie "Senden an >...
Methodenauswahl Zweck der Methodenauswahl Sie können in Ihrem DMA 35 Messmethoden definieren und speichern. Das Verwenden von Messmethoden trägt wesentlich zur effizienteren Gestaltung Ihres Messablaufes bei, speziell wenn Sie mit dem gleichen Gerät mehrere unterschiedliche Stoffe hinsichtlich verschiedener Messgrößen untersuchen wollen.
9.2.2 Methodenliste eingeben Wenn Sie umfangreiche Methodenlisten anlegen oder bearbeiten wollen, können Sie dies bequem am PC machen und dann die Daten auf das DMA 35 importieren. Wenn Sie über mehrere DMA 35 Dichtemessgeräte verfügen, können Sie auf diesem Weg die gleiche Methodenliste auf mehrere Geräte importieren, um mehrere identische...
Seite 116
Wenn Ihr PC über keine IrDA-Schnittstelle verfügt, installieren Sie den IrDA- USB-Adapter auf Ihrem PC. Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Nachdem Sie ein bis zwei Methoden wie oben beschrieben am Gerät angelegt haben, drücken Sie <Menü>...
Drücken Sie <Menü> und wählen Sie "Einstellungen > Import / Export > Vom PC empfangen". Halten Sie die IrDA-Schnittstelle des DMA 35 erneut zur IrDA-Schnittstelle des PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Klicken Sie am PC mit der rechten Maustaste auf die Datei, die Sie senden möchten und wählen Sie "Senden an >...
9.2.5 Alle Methoden löschen Drücken Sie <Menü> und wählen Sie "Methoden > Methode bearbeiten". Wählen Sie eine beliebige Methode und drücken Sie Wählen Sie <Alle löschen>. Drücken Sie <Löschen>, wenn Sie gefragt werden ob Sie wirklich alle Methoden löschen wollen. Alle Methoden werden gelöscht.
9.3.2 Proben-ID-Listen eingeben Wenn Sie umfangreiche Proben-ID-Listen anlegen oder bearbeiten wollen, können Sie dies bequem am PC machen und dann die Daten in das DMA 35 importieren. Um Einsicht in das anzuwendende Format zu bekommen, legen Sie in einem ersten Schritt ein bis zwei Proben-IDs am Gerät selbst an (siehe Kapitel 9.3.1) und...
Seite 120
Wenn Ihr PC über keine IrDA-Schnittstelle verfügt, installieren Sie den IrDA- USB-Adapter auf Ihrem PC. Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Nachdem Sie ein bis zwei Proben-IDs wie oben beschrieben am Gerät angelegt haben, drücken Sie <Menü>...
PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Klicken Sie am PC mit der rechten Maustaste auf die Datei, die Sie senden möchten, und wählen Sie "Senden an > Computer in Reichweite". Die Proben-ID-Liste wird an das DMA 35 gesendet und automatisch übernommen. 9.3.3 Proben-ID bearbeiten Drücken Sie <Menü>...
Der Name der ID wird in der Hauptansicht angezeigt. Messmodus wählen Das DMA 35 bietet drei verschiedene Messmodi - "Genau", "Schnell" und "Manuell". Abhängig vom eingestellten Messmodus müssen unterschiedliche Stabilitätskriterien erfüllt sein, bevor das Messergebnis gespeichert wird. Das Stabilitätskriterium bezieht sich immer auf die Temperatur: •...
RFID-Funktion nutzen (nur für Versionen mit RFID-Schnittstelle) Die Versionen DMA 35 Tag&Log, DMA 35 Ex und DMA 35 Ex Petrol sind mit einer RFID-Schnittstelle ausgestattet, welche es Ihnen ermöglicht einen eindeutigen Zusammenhang zwischen einer Methode und/oder Proben-ID und einem RFID-Tag herzustellen.
Sie können sowohl während der Eingabe einer neuen Methode (siehe Kapitel 9.2.1) oder Proben-ID (siehe Kapitel 9.3.1) als auch während der Bearbeitung einer Methode (siehe Kapitel 9.2.3) oder Proben-ID (siehe Kapitel 9.3.3) einen RFID-Tag zuweisen. Gehen Sie hierzu in das entsprechende Menü wie im zutreffenden Kapitel beschrieben.
Wiederholen Sie diesen Vorgang für andere Proben-IDs und/oder Methoden die Sie auf anderen RFID-Tags speichern möchten. Nachdem alle Proben-IDs und/oder Methoden an einen Tag gesendet wurden, können Sie die Proben-ID-Liste (siehe Kapitel 9.3.5) und/oder Methodenliste (siehe Kapitel 9.2.5) vom Gerät löschen. 9.5.4 RFID-Tags löschen Im Falle, dass während des Programmierens des RFID-Tags ein Fehler aufgetreten ist oder Sie den RFID-Tag für eine andere Proben-ID und/oder Methode verwenden...
Halten Sie den nächsten RFID-Tag zur RFID-Schnittstelle des Geräts, bis die RFID-Information angezeigt wird oder verlassen Sie das "RFID Information" Menü. 9.5.6 Methode und/oder Proben-ID mittels RFID auswählen Diese Art der Auswahl funktioniert nur, wenn Sie zuvor einer oder mehreren Methoden und/oder Proben-IDs einen RFID-Tag zugeordnet haben (siehe Kapitel 9.5.2) oder einen oder mehrere RFID-Tags mit Methoden und/oder Proben-IDs programmiert haben.
Probe einfüllen Sie können die Probe je nach Viskosität der einzufüllenden Probe über das Saugrohr oder den Spritzenadapter in die Messzelle füllen. Bei hoch viskosen Proben empfehlen wir das Einfüllen mithilfe der Spritze. 9.6.1 Einfüllen über das Saugrohr Drücken Sie den Pumpenknopf bis zum Anschlag nach unten (siehe Abb. 9 - 1). Tauchen Sie das Saugrohr in die zu messende Probe ein.
Probe zuordnen wollen (siehe Kapitel 9.3). Befüllen Sie die Messzelle mit der zu messenden Probe. Drücken Sie die Taste auf der Rückseite des DMA 35. Der Messwert wird angezeigt, sobald sich das Messergebnis stabilisiert hat, und mit allen mitgeltenden Daten in der Ergebnisliste gespeichert.
Schalten Sie den Drucker mit IrDA-Schnittstelle ein. Drücken Sie die <Drucken> Taste, wenn der Messwert auf dem Display erscheint. Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des Druckers, um die Kommunikation zwischen den Geräten aufzubauen. Der Messwert wird nun gedruckt.
Abb. 9 - 3 Messdaten Messdaten zum PC exportieren Der Export von Messdaten zum PC erfordert kein spezielles Programm. Sie brauchen nur einen PC, der eine Infrarotschnittstelle oder einen IrDA-USB-Adapter angebracht und installiert hat. Kontaktieren Sie Ihren Anton-Paar-Vertreter, falls Sie einen IrDA- USB-Adapter für Ihren PC benötigen.
Seite 131
Wählen Sie mithilfe der Pfeiltasten den Messwert aus, den Sie exportieren wollen. Drücken Sie <Export>. Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Wählen Sie nun <Auswahl exportieren>, um den ausgewählten Messwert auf den PC zu exportieren.
Drücken Sie <Export>. Wählen Sie nun <Auswahl drucken>, um den ausgewählten Messwert auszudrucken. Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des Druckers, um die Kommunikation zwischen den Geräten aufzubauen. Der Messwert wird nun gedruckt. Alle gespeicherten Messdaten drucken Schalten Sie den Drucker mit IrDA-Schnittstelle ein.
9.11 Gespeicherte Messdaten löschen Den letzten Messwert löschen Drücken Sie <Menü> und wählen Sie "Messdaten". Wählen Sie einen Messwert aus und drücken Sie Wählen Sie <Letzten löschen> und drücken Sie <OK>. Drücken Sie <Löschen> wenn Sie gefragt werden, ob Sie den letzten Messwert wirklich löschen wollen.
10 Gerät reinigen und lagern 10.1 Messzelle reinigen Um langfristig genaue Messresultate zu erzielen, ist es notwendig, die Messzelle vor und nach jeder Messserie mit einem geeigneten Lösungsmittel zu reinigen. Wird die Messzelle nicht ausreichend gereinigt, kann es zur Belagbildung in der Messzelle kommen, wodurch Messungenauigkeiten entstehen können.
10.3 Pumpengehäuse reinigen Da das DMA 35 nach außen hin und zur Pumpe hin abgedichtet ist, können Sie das Pumpengehäuse im Falle der Verschmutzung mit fließendem Leitungswasser spülen. Halten Sie hierzu das Saugrohr in ein Gefäß, dass für die Entsorgung der Probe geeignet ist.
Wartung 11.1 Batterien wechseln Der Ladestand der Batterie ist am Symbol in der Informationsleiste rechts oben ersichtlich. Folgende Ladezustände sind möglich: Batterie voll Batterie etwas schwach Batterie schwach Batterie leer Wenn die Batterien fast leer sind, wird die Warnung "Batterie schwach" ausgegeben. Nach einer zweiten Warnung "Batterie leer"...
Seite 137
Ladezustand. • Verwenden Sie für DMA-35-Versionen mit ATEX- Kennzeichnung (DMA 35 Ex und DMA 35 Ex Petrol) nur den für Ex-Versionen zugelassenen Batterietyp EN91 (LR06, AA) von Energizer Industrial. Halten Sie das Saugrohr in ein Gefäß, dass für die Entsorgung der Probe geeignet ist.
Seite 138
Entfernen Sie die Pumpenverriegelung durch eine Schiebebewegung zum Außenrand des Geräts hin. Abb. 11 - 3 Pumpenverriegelung entfernen Nehmen Sie eine Münze zur Hand und öffnen Sie mit einer Drehbewegung den Batterieverschluss. Abb. 11 - 4 Batterieverschluss öffnen Entfernen Sie die leeren Batterien, indem Sie das Gerät überkopf drehen. Setzen Sie die neuen Batterien ein.
11.2 Firmware-Update durchführen Ihr Anton-Paar-Vertreter wird Sie informieren, wenn ein neues Firmware-Update für Ihr DMA 35 verfügbar ist. Nach Erhalt der Update-Datei können Sie diese selbständig auf Ihr Gerät importieren. Wenn Ihr PC über keine IrDA-Schnittstelle verfügt, installieren Sie den IrDA- USB-Adapter auf Ihrem PC.
Drücken Sie <Menü> und wählen Sie "Einstellungen > Import / Export > Zum PC senden > Geräteinformation". Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Auf Ihrem PC-Bildschirm erscheint ein Informationsfenster mit der Frage, ob Sie die Datei annehmen wollen.
Drücken Sie <Menü> und wählen Sie "Einstellungen > Import / Export > Zum PC senden > Justierung". Halten Sie die IrDA-Schnittstelle des DMA 35 zur IrDA-Schnittstelle des PCs, um die Kommunikation zwischen den beiden Geräten aufzubauen. Auf Ihrem PC-Bildschirm erscheint ein Informationsfenster mit der Frage, ob Sie die Datei annehmen wollen.
12 Nachjustierung Um genaue Messresultate zu erzielen, ist es notwendig, die Messzelle vor und nach jeder Messserie zu reinigen. Wird die Messzelle nicht ausreichend gereinigt, kann es zur Belagbildung in der Messzelle kommen. Diese Veränderung kann an abweichenden Dichtewerten für deionisiertes Wasser erkannt werden. Führen Sie daher in regelmäßigen Abständen Kontrollmessungen mit deionisiertem Wasser durch.
Der Dichtewert des eingefüllten deionisierten Wassers wird nun gemessen und mit den Justierdaten verglichen. Auf dem Display erscheint die errechnete Abweichung (Delta) in g/cm Drücken Sie <OK>, um die neue Justierung zu aktivieren. 12.3 Kundenjustierung Sie können auch eine beliebige andere Referenzflüssigkeit mit bekannter Dichte bei 20 °C und bekanntem Temperaturkoeffizienten für Ihre Nachjustierung heranziehen.
12.4 Offset festlegen Sie können für Ihre Messung einen Offsetwert bestimmen, der automatisch zu jedem gemessenen Wert hinzugezählt wird. Der Offsetwert ist immer auf die aktuelle Messgröße bezogen und wird gelöscht, wenn Sie zu einer anderen Messgröße wechseln. Haben Sie eine Methode gewählt, so wird der gewählte Offsetwert gemeinsam mit der Methode gespeichert.
Die Batterie ist leer. Fehler 01 Die Temperatur ist ungültig. Fehler 02 Die Periode ist ungültig. Fehler 03 DMA 35 hat keine Justierdaten. Fehler 04 Berechnungsfehler ACHTUNG Treten die Fehlermeldungen "Fehler 01" bis "Fehler 04" auf, senden Sie Ihr Gerät zum Service.
LCD monochrom, grafisch, 41 x 55 mm, 160 x 240 Pixel Datenspeicher: 1024 Messdaten Schnittstellen: DMA 35: IrOBEX/IrLPT DMA 35 Tag&Log, DMA 35 Ex und DMA 35 Ex Petrol: IrOBEX/IrLPT, RFID Stromversorgung: Batterietype: Alkalibatterie 1,5V LR06 MIGNON AA vom Typ "Energizer EN91 Industrial"...
Gehäuse für DMA 35 Ex Petrol PP (Polypropylene) Faradex MS002 Gehäuse für DMA 35, DMA 35 Tag&Log und DMA 35 Ex PTFE (Polytetrafluoroethylen) Saugrohr PVDF (Polyvinylidenfluorid) Verbindungsblock, Schraube Viton O-Ring für DMA 35, DMA 35 Tag&Log und DMA 35 Ex C96IB01...
Anhang B: Details zu den Messgrößen Messgröße Min. Max. Einheit Format Offset- Format 0.0000 3.0000 g/cm³ n.nnnn 0.0nnn Dichte 0000.0 3000.0 kg/m³ nnnn.n 00nn.n 0.0000 3.0000 g/cm³ n.nnnn 0.0nnn Dichte @ xx °C 0000.0 3000.0 kg/m³ nnnn.n 00nn.n Rel. Dichte SG 0.0000 3.0000 n.nnnn...
Seite 151
0.5000 1.5000 g/cm³ nnnn.n 0.0nnn API Dichte A 0500.0 1500.0 kg/m³ n.nnnn 00nn.n 0.5000 1.5000 g/cm³ nnnn.n 0.0nnn API Dichte B 0500.0 1500.0 kg/m³ n.nnnn 00nn.n 0.5000 1.5000 g/cm³ nnnn.n 0.0nnn API Dichte D 0500.0 1500.0 kg/m³ n.nnnn 00nn.n Kundenfunktionen Abhängig von der ausgewählten Temperatureinheit (°C oder °F) werden die API- Werte automatisch @ 15 °C oder @ 60 °F angezeigt.
Seite 152
10 H2SO4 @ 20 °C Alkohol % v/v @ 20 °C 12 Alkohol % w/w 13 Alkohol US @ 60 °F 14 API Zahl A 15 API Zahl B 16 API Zahl D 17 API SG A 18 API SG B 19 API SG D 20 API Dichte A 21 API Dichte B...
Anhang G: Menübaum Messdaten Export Alle exportieren Auswahl exportieren Alle drucken Auswahl drucken Proben-ID ID auswählen Neue ID eingeben ID bearbeiten ID an RFID senden Methoden Methode auswählen Neue Methode Methode bearbeiten Methode an RFID Messgröße Dichte Dichte Dichte @ xx °C Relative Dichte SG Alkohol Alkohol % v/v @ 20 °C...
Seite 161
Einstellungen Messmodus Genau; Schnell; Manuell Import / Export Zum PC senden Kundenfunktionen Justierung Geräteinformation Proben-ID Liste Methoden Einstellungen Messdaten Vom PC empfangen Datenformat Format: CSV; TXT Trennzeichen: . ; / Dezimalzeichen: . , Passwort Neues Passwort Datum und Zeit Datum und Zeit Datumsformat TT.MM.JJ TT.MM.JJJJ...
Seite 162
Anton Paar GmbH ® Anton-Paar-Str. 20 A-8054 Graz Austria - Europe Tel: +43 (0)316 257-0 Fax: +43 (0)316 257-257 E-mail: info@anton-paar.com Web: www.anton-paar.com Instruments for: Density & concentration measurement Rheometry & viscometry Sample preparation Microwave synthesis Colloid science X-ray structure analysis...