Herunterladen Inhalt Inhalt Diese Seite drucken

Die Frästrommel; Milling Drum - Airtec ROTO-MAT RM-320 Betriebsanleitung/Ersatzteilliste

Vorschau ausblenden Andere Handbücher für ROTO-MAT RM-320:
Inhaltsverzeichnis

Werbung

RM-320 Kap.7
Betriebsanleitung
Wartung
Vor Beginn jeder Instandsetzung
an
der
Maschine
Antrieben
sind
diese
unbeabsichtigtem Einschalten zu
sichern.
Mit
dem
Ziehen
Netzsteckers
Zündkerzensteckers
möglich.
Verwenden Sie nur AIRTEC-
Originalteile
7.4 Die Frästrommel
Die
Frästrommel
hochbeanspruchtes Bauteil Ihrer
Fräsmaschine
und
sollte
Ihre
besondere
Aufmerksamkeit
bei
der
Wartung
Instandsetzung haben.
Wird
die
Frästrommel
ausgetauscht, sollte jedesmal die
Antriebswelle
gereinigt
eingefettet werden, damit beim
nächsten Wechsel der Trommel
keine
Rost
Schmutzablagerungen
Arbeiten erschweren.
Falls
die
Frästrommel
Neubestückung
oder
von
Bauteilen
zerlegt
sollte,
muss
unbedingt
geachtet
werden,
Anordnung
der
Fräswerkzeuge
und
Zwischenscheiben
beigefügtem
Bestückungsschema
eingehalten wird. Ausserdem ist
darauf
zu
achten,
Bohrungen
für
die
nicht ausgeschlagen sind und die
Schrauben fest angezogen sind.
Instructions de service
Maintenance
Avant toute réparation sur la
und
deren
machine et ses moteurs, prévenir
vor
tout démarrage inopiné. Il suffit
à cet égard de retirer la prise
des
secteur ou la cosse de bougie.
bzw.
ist
dies
N'utilisez que des pièces
d'origine AIRTEC.
7.4 Le tambour de fraise
ist
ein
Le tambour de fraise est un élé-
ment très sollicité. Accordez-lui
daher
pour cette raison une attention
particulière lors de la mainte-
und
nance et des réparations.
Lors du remplacement du tam-
bour de fraise, nettoyez et grais-
und
sez l'arbre d'entraînement afin
qu'aucune trace de rouille ou
d'encrassement ne complique les
oder
travaux lors du prochain rempla-
die
cement de tambour.
zwecks
Si le tambour de fraise doit être
Austausch
démonté
werden
changement d'équipement ou le
darauf
remplacement de pièces, il est
dass
die
impératif de veiller à ce que la
disposition des outils de fraisage
lt.
et
des
corresponde
d'équipement joint. Veillez en
dass
die
outre à ce que les alésages de la
Querachsen
plaque de couverture pour les
axes transversaux ne soient pas
déviés et que les vis soient bien
serrées.
pour
permettre
un-
disques
intermédiaires
bien
au
schéma
37
Instruction Manual
Maintenance
03/01/2004
Before starting repair work on
the machine and the drives,
make
sure
they
cannot
switched on accidentally. Pulling
out the mains plug or the spark
plug will safeguard the machine.
Use only AIRTEC original
parts

7.4 Milling drum

The milling drum is a highly
stressed
component
milling machine and special at-
tention should be paid to it dur-
ing maintenance and repairs.
If the milling drum is replaced,
always clean and lubricate the
drive shaft so that the next time
the drum is replaced rust or
deposits of dirt do not make
work more difficult.
If the milling drum has to be
dismantled for new parts to be
fitted or components replaced,
make sure that the arrangement
of the milling tools and the
spacers as shown in the en-
closed components schema is
kept to. In addition, make sure
that the holes in the covering
plate for the lateral axle are not
worn out and the screws are
tight.
AIRTEC
be
of
your

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis