Running In The Tool - Bostitch BTCN560 Bersetzt Von Den Originalanweisungen

Preparing the Tool (Fig. A)
1. Remove the battery pack
tool is locked off.
2. Remove all nails from the magazine
3. Check if the contact trip
4. Reload the nails to the magazine.
5. Insert battery pack.

WARNING: Do not use the tool if the contact trip or nail
pusher cannot move freely.
NOTICE: NEVER spray or in any
other way apply lubricants or cleaning
solvents inside the tool. This can
seriously affect the life and performance
of the tool.

Running in the tool

Please note that this tool requires a run-in period before it
operates with full power due to parts which need to mesh or
wear in together. It may be that the tool does not drive long
nails flush consistently during this period. After driving between
500 and 1000 nails the tool should have run-in and perform at
full capacity.
Actuating the Tool (Fig. A)
The BTCN560 can be operated using one of two modes:
sequential action mode or bump action mode.
The BTCN565 can be operated using one of two modes:
sequential action mode or RapidCycle mode.
Bump action Mode (BTCN560 ONLY)
The bump action mode is used for rapid nailing on flat,
stationary surfaces and typically most effective for applications
driving shorter nails.
1. Using the mode selector switch
action mode ( ).
2. Release the trigger safety lock-off
a. To drive a single nail, operate the tool as described for
sequential action:
b. Push the contact trip
c. Pull the trigger switch
pull with the contact trip pushed against the work
surface will drive one nail.
3. To drive several nails, depress and hold the trigger switch
and then push the contact trip
work surface.

WARNING: Do not keep the trigger depressed when the
tool is not in use. Keep the trigger safety lock-off
locked position to prevent accidental actuation when the
tool is not in use.
4. When changing between sequential and bump modes,
it may be necessary to adjust the driving depth. Refer to
Adjusting the Driving Depth for instructions.
Sequential action mode
The sequential action mode is used for intermittent nailing
when very careful and accurate placement is desired. It
12 from the tool and ensure the
.
7
can move freely.
3
9 to select the bump
2 .
3 against the work surface.
1 to actuate the tool. Each trigger
3 repeatedly against the
2
also offers the maximum delivery of power for driving the
longest nails.
1. Using the mode selector switch
action mode (
2. Release the trigger safety lock-off
3. Push the contact trip
4. Pull the trigger switch
5. Release the trigger and raise the nailer from the
work surface.
6. Repeat steps 3–5 to actuate the next nail.
RapidCycle Mode (BTCN565)
The RapidCycle mode is ideal for when the user fires many nails
in a sequence and needs to move more rapidly. The tool still
operates in a full sequential mode, but the motor readies itself
for the next nail immediately after firing to minimise time spent
waiting for the motor to get up to speed.
1. Use the mode selector switch
mode ( ).
2. Release the trigger safety lock-off
3. To drive a single nail, operate the tool as described in the
sequential action:
Push the contact trip
-
Pull the trigger switch
-
hear the motor spin up after the nail has been driven).
4. To drive several nails simply repeat the directions in point
3. above. If you do not fire a nail within 2 seconds of the
previous then the motor will coast down to rest.
Using the Trigger Lock-off (Fig. C)
Each Bostitch nailer is equipped with a trigger lock-off
when pushed to the right as shown in Figure C, prevents the
tool from firing a nail by locking the trigger and bypassing
power to the motor.
When the trigger lock-off is pressed to the left, the tool will be
fully operational. The trigger lock-off should always be locked
off whenever any adjustments are made or when tool is not in
immediate use.
Non-mar Tip (Fig. A)
When using this tool on materials that you do not want to mark,
such as wood cladding, use the plastic non-mar tip
, contact trip 3 .
1
LED Indicator (Fig. A)
Your nailer is equipped with two LED indicator lights
on the back of the tool just below the back cap. Also refer to to
in the
the Troubleshooting Guide for further instruction.
, select the sequential
9
).
2 .
3 against the work surface.
1 to actuate the tool.
to select the RapidCycle
9
2 .
against the work piece.
3
to actuate the tool. (You will
1
LOW BaTTERY
Replace battery with a
charged pack.
hOT Pack
Let the battery cool or replace it with
a cool pack.
EnGLIsh
2 which
over the
13
located
5
41