Bostitch BTCN560 Bersetzt Von Den Originalanweisungen Seite 42

EnGLIsh
subject to variation based on product components, temperature
and end-user application.
Rotating Rafter/Belt Hook (Fig. F)
The rafter/belt hook 10 and can be easily positioned to the left
or right of the tool to accommodate left- or right-handed users.
If use of the hook is not desired at all, it can be rotated to the
front or back of the handle base.
Loading the Tool (Fig. D)

WARNING: Always lock tool off and disconnect battery
pack before loading and unloading fasteners.
1. Slide the spring-loaded pusher latch
magazine to lock it into place.
2. Select an appropriate collated nail stick. (Refer to Technical
Data.) Bostitch would always recommend that you use
Bostitch branded first fix nails.

WARNING: Since accessories, other than those offered
by Bostitch, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only Bostitch recommended
accessories should be used with this product.
3. Insert collated nail stick into the loading slot on side of the
magazine. Be sure the fasteners ride on their heads in the
nail channel.
4. Close the magazine by releasing the pusher latch. Carefully
allow the latch to slide forward and engage the nail strip.
Dry Fire Lock out
The nailer is equipped with a dry fire lock out which restricts the
tool from actuating when the magazine is nearly empty. When
approximately 7 to 9 nails remain in the magazine, the tool dry
fire lock actuates. Refer to Loading the Tool to reload a stick of
collated nails.
nOTE: If heavy force is placed on the tool it is possible to
override the lock out. This protects the tool from potential
damage if dropped.
Adjusting the Driving Depth (Fig. E)
The nail driving depth can be adjusted using the depth
adjustment wheel.
1. To drive the nail shallower, rotate the depth adjustment
wheel to the left, toward the shallow nail icon.
4
2. To sink a nail deeper, rotate the depth adjustment wheel
to the right, toward the deeper nail icon.
Selecting the Mode (Fig. A)
BTCN560
To select sequential action mode, slide the mode selector
switch 9 to display the single nail
icon ( ).
To select bump action mode, slide the mode selector switch
to display the three nail
icon ( ).
40
8 to the base of the
4
9
nOTE: Maximum power for driving long nails is achieved in
sequential mode, so limit use of bump mode when driving
longer nails.
BTCN565
To select standard sequential mode, slide the mode selector
switch 9 to display the single arrow ( ) icon.
To select RapidCycle sequential action mode, slide the mode
selector switch 9 to display the double arrow (
nOTE: Battery life in RapidCycle sequential mode will be shorter
than in standard sequential mode. Leaving the tool in standard
sequential will give maximum battery life.
Speed Selection (Fig. A)
This nailer is equipped with a dual speed selection switch
located on the foot.
1. For shorter nails, select speed 1 by setting the switch to the
left most position.
2. For longer nails and more rigorous applications, select speed
2 by setting the switch to the right most position.
nOTE: In the event that nails are not driving to depth in
speed setting 1, you may have to switch to speed setting 2 for
additional driving power.
nOTE: Firing nails under 76 mm (3") in length using Speed
Setting 2 will cause excessive wear to your tool and may result
in early failures.
Suggested Speed Settings
Application Typical Nail Length
Framing & Decking 8.255 cm, 8.89 cm
General Framing 7.62 cm
Sheathing 6.03 cm
Fencing 5.08 cm
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
as shown.
) icon.
14
Speed Setting
2
1
1
1
16