Special Work Related To The Maintenance And Repair Of The Machine; Information About Special Risks With Electrical Energy - GÖLZ FS175 Bedienungsanleitung

FS175
2.6 Special work related to the
maintenance and repair of the
machine
Observe the adjustment, maintenance and inspection
activities and intervals set out in the operating
instructions, including information on the replacement
of parts and equipment! These activities may be
executed by skilled personnel only.
Brief operating personnel before beginning special
operations or maintenance work, and appoint a person
to supervise the activities.
In any work concerning the operation, conversion or
adjustment of the machine and it's safety-oriented
devices or any work related to maintenance, inspection
and repair, always observe the start-up and shut-down
procedures described in the operating instructions and
the information on maintenance work. Ensure that the
maintenance area is adequately secured.
Carry out maintenance and repair work only of the
machine is positioned on stable and level ground and
has been secured against inadvertent movement and
buckling. If the machine is completely shut down for
maintenance and repair work, it must be secured
against inadvertent starting.
To avoid the risk of accidents, individual parts and
large assemblies being moved for replacement
purposes should be carefully attached to lifting tackle
and secured. Use only suitable and technically perfect
lifting gear and suspension systems with adequate
lifting capacity. Never work or stand under suspended
loads.
The fastening of loads and the instructing of crane
operators should be entrusted to experienced persons
only. The marshaller giving the instructions must be
within sight or sound of the operator.
For carrying out overhead assembly work always use
specially designed or otherwise safety-oriented ladders
and working platforms. Never use machine parts as a
climbing aid. Wear safety harness when carrying out
maintenance work at greater heights.
Clean the machine, especially connections and
threaded unions, of any traces of oil, fuel or
preservatives before carrying out maintenance / repair.
Never use aggressive detergents. Use lint-free
cleaning rags.
Before cleaning the machine with water, steam jet or
detergents, cover or tape up all openings which -for
safety and functional reasons - must be protected
against water, steam or detergent penetration.
Do not clean the machine with a high-pressure
cleaner. The hard water jet can put damage to parts of
the machine. After cleaning, remove all covers and
tapes applied for that purpose.
After cleaning check
connections, chafe marks and damage! Have identified
defects repaired immediately!
Always tighten any screwed connections that have
been loosened during maintenance and repair.
the machine for loose
Any safety devices removed for set-up, maintenance
or repair purposes must be refitted and checked
immediately upon completion of the maintenance and
repair work. Ensure that all consumables and replaced
parts are disposed of safely and with minimum
environmental impact.
2.7 Information about special risks
with electrical energy
Observe the relevant national regulations or standards.
Electrical connections must always be kept free from
dirt and moisture.
Use only original fuses with the specified rating! Switch
off the machine immediately, if trouble occurs in the
electric power supply!
If your machine comes into contact with a live wire:
warn others against approaching and touching the
•
machine
have the live wire de-energized
•
When working with the machine, maintain a safe
distance from overhead electric lines. If work is to be
carried out close to overhead lines, the working
equipment must be kept well away from them.
Caution, danger to life!
Check out the prescribed safety distances.
•
Work on the electrical system or equipment may
•
only be carried out by a skilled electrician himself
or by specially instructed personnel under the
control and supervision of such electrician and in
accordance with the applicable engineering rules.
If provided for in the regulations, the power supply
•
to parts of machines and plants, on which
inspection, maintenance and repair work is to be
carried out must be cut off.
Before starting work, check the de-energized
•
parts for the presence of power and ground or
short-circuit them in addition to insulating adjacent
live parts and elements.
The electrical equipment of machines is to be
inspected and checked at regular intervals. Defects
such as loose connections or scorched cables must be
rectified immediately.
Necessary work on live parts and elements must be
carried out only in the presence of a second person
who can cut off the power supply in case of danger by
actuating the emergency shut-off or main power
switch. Secure the working area with a red-and white
safety chain and a warning sign. Use insulated tools
only.
If mobile electrical equipment, connecting cables and/
or extension/ appliance cords with plug connectors are
used, ensure that such equipment, cables and cords
are checked for correct function at least once every six
months by a qualified electrician or - if suitable testing
equipment is available - by a properly instructed
person.
- 27-
®
5007287-01
BA-DE-GB-FR-NL