Selection And Qualification Of Person; Safety Instructions Governing Specific Operational Phases - GÖLZ FS175 Bedienungsanleitung

FS175
GmbH prior approval! This also applies to the installation
and adjustment of safety devices as well as to welding
and cutting work on supporting structures.
Damaged or worn parts of the product must be replaced
immediately. Use genuine spare parts only.
All spare parts and tools must comply with the technical
requirements specified by the manufacturer/ distributor.
Adhere to the legally prescribed preventive maintenance
and inspection intervals or those specified in this
operating manual!
Hydraulic hose pipes must be changed within the
specified or appropriate intervals, even if no safety-
relevant defects are visible.
All maintenance and repair activities must be performed
by qualified personnel using suitable tools and other
suitable workshop equipment. Observe the fire alarm and
fire fighting measures. The personnel must be made
familiar with the location
extinguishers!
2.4 Selection and qualification of
person
Only permitted personnel is allowed to work on and with
the machine! The legal minimum age is to be observed!
Only assign trained and instructed personnel! Clearly
define the responsibilites of the personnel with regard to
operating, setting-up, maintaining and repairing the
®
machine! The GÖLZ GmbH can assist you in training
your personnel.
Make sure that only instructed and competent personnel
works on the machine. Define the responsibility of the
machine operator, also in terms of traffic regulations and
enable him to refuse instructions of third parties which
breach safety regulations.
Personnel that is to be trained or to be instructed or that
is serving a general training is only to be permitted to
operate the machine under the supervision of an
experienced person.
To operate the machine you must be rested, in good
physical condition and mental health. If you have any
condition that might be aggravated by strenuous work,
check with your doctor before operating with the machine.
Do not operate the machine if you are under the influence
of any substance (drugs, alcohol) which might impair
vision, dexterity or judgment.
Works on electrical, pneumatic, combustion and hydraulic
fittings and equipment are only to be carried out by
qualified personnel or instructed people being directed
and supervised by qualified personnel in compliance with
the respective rules!
2.5 Safety instructions governing
specific operational phases
Before work
Avoid any operational mode that might be prejudicial to
safety!
Before beginning work, familiarize yourself with the
surroundings and circumstances of the site, such as
and handling of fire
- 26-
obstacles in the working and travelling area, the soil
bearing capacity and any barriers separating the
construction site from public roads.
Take the necessary precautions to ensure that the
machine is used only when in a safe and reliable state.
Operate the machine only if all protective and safety-
oriented devices, such as removable safety devices,
emergency shut-off equipment, sound-proofing elements
and exhausters, are in place and fully functional.
Regard all safety specifications!
Check the machine at least once per working shift for
obvious damage and defects. Report any changes (incl.
changes in the machine's working behaviour) to the
competent organization/
necessary, stop the machine immediately and lock it.
Have any defects rectified immediately. At any time,
ensure the operator has sufficient view to his working
area, in order to have intervention to the working process.
Wet cutting is to be accomplished while working. This
prevents the appearance of particulate matter and
increases the life-time of the diamond tool. During start-
up and shut-down procedures always watch the
indicators in accordance with the operating instructions!
Before starting or setting the machine in motion, make
sure that nobody is at risk. Keep children and
unauthorized persons away from the work area.
Noise protection equipment on the unit must be in
protective position during operation. Wear the required
individual ear protection!
Always keep at a distance from the edges of building pits
and slopes. Avoid any operation that might be a risk to
machine stability! Keep the work area clean. Cluttered
areas and benches invite injuries! Do not operate when
you are tired! Watch what you are doing! Risk of
stumbling! Cables and hoses must complete rolling up.
After assembly do not leave any tools, a wrench for
example, on the unit.
Check to see that the tools are removed from the
machine before operating! Damaged blades have to be
changed immediately. Use only recommended blades
®
from the GÖLZ GmbH.
Control the working area for water-, gas- and electrical
lines!
Important:
accomplished
prevents the appearance of particulate
matter and increases the life-time of the
diamond tool!
During work
Make sure, that the machine is well fastened before
and while cutting!
Never touch rotating parts like blade shaft or blade!
After work
Before leaving the machine always secure it against
unauthorized use!
person immediately.
Wet cutting is to
while working!
5007287-01
BA-DE-GB-FR-NL
®
If
be
This