Setting The Working Positions; Switching On And Off - FLORABEST FLV 1200 A1 Originalbetriebsanleitung

body positions and
the implement repaired the implement repaired
G B R I E
always keep your
must be replaced by the must be replaced by the
by an authorised
by an authorised
balance, so that you
manufacturer, a customer manufacturer, a customer
Operation
workshop!
workshop!
continually have a sure
service agent of the same service agent of the same
• Store the implement in a • Store the implement in a
Please observe local regulations
footing on slopes. Always
or a similarly qualified or a similarly qualified
concerning noise protection.
dry place well out of dry place well out of
work across slopes - never
person in order to prevent person in order to prevent
reach of children.
reach of children.

Setting the working positions

up and down! Be
hazards. hazards.
particularly careful when
The implement has 4 principal position
• Keep the extension cables • Keep the extension cables
CAUTION! The CAUTION! The
settings:
changing the travelling
away from the sprung away from the sprung
following states how following states how
direction.
tines and verticutor knives. tines and verticutor knives.
to avoid damage to the
to avoid damage to the
Do not work on very
They may damage the They may damage the
implement and any implement and any
steep slopes. This enables
cables and result in cables and result in
resulting harm to resulting harm to
you to control the
contact with live parts. contact with live parts.
people: people:
equipment better in
• Check that the mains • Check that the mains
Setting 0 :
unexpected situations.
voltage is the same as voltage is the same as
This position sets the maximum safety spac
Take care of your Take care of your
• Do not run! Always guide
indicated on the rating indicated on the rating
implement: implement:
the implement at a
plate. plate.
Setting 1 :
• Switch off the power
• Switch off the power
Set this position when working with a new
walking pace with both
• Avoid body contact with • Avoid body contact with
implement.
when the implement is to
when the implement is to
hands on the handle. Be
earthed parts (e.g. metal earthed parts (e.g. metal
be carried across steps. be carried across steps.
Settings 2 - 3 :
especially careful when
fences, metal posts). There fences, metal posts). There
• Inspect the implement • Inspect the implement
The working position can be lowered with you turn the implement
is an increased risk of is an increased risk of
increased knife and sprung tine wear. each time before it is to
each time before it is to
around or draw it
electric shock if your body electric shock if your body
be used. Never operate
be used. Never operate
towards you. Danger of
ingly poor result. is earthed. is earthed.
the implement if safety the implement if safety
The readjusting depth amounts to approx.
stumbling!
• Only use approved • Only use approved
3 mm per setting.
devices (e.g. impact devices (e.g. impact
• Start or actuate the
extension cables of the extension cables of the
The implement is delivered with
protector, parts of the
protector, parts of the
starting lever with care
type H05RN-F with a type H05RN-F with a
the height set to the Transport
cutting facility or bolts)
cutting facility or bolts)
Position (0).
and in conformity with the
maximum length of 75 m maximum length of 75 m
1. The implement must be switched off to
are missing, worn out or are missing, worn out or
directions in these
and which have been and which have been
set the working position.
damaged. damaged.
2. Pull the adjustment wheel for adjustment
approved for open-air approved for open-air
(see A 9) and turn it to the desired
use. The stranded cord use. The stranded cord
position until it clicks into place.
Both wheels (right and left) must be in-
dividually set to the same position.
18
Transport position
Working position
Readjustment positions
Instructions.
Check especially the Check especially the
• Do not tilt the implement
diameter of the extension diameter of the extension
power cable and starting power cable and starting
when starting, other than
cable must be at least 2.5 cable must be at least 2.5
The adjustment wheel is not intended
lever for damage.
lever for damage.
it has to be lifted. In this
for height adjustment but rather to
mm². Always unreel a mm². Always unreel a
To avoid imbalance, all
To avoid imbalance, all
compensate for wear. Selection of
case tilt the implement
cable drum to its full cable drum to its full
a readjustment position without the
tools and bolts must be tools and bolts must be
only to the extent that is
corresponding wear can overload
length so that the entire length so that the entire
exchanged as complete exchanged as complete
the motor and damage the cylinder.
absolutely necessary and
cable can be checked for cable can be checked for
sets.
sets.

Switching on and off

always lift the implement
damage. damage.
• Only use spare parts and
• Only use spare parts and
on the side that is
• Use the included cable • Use the included cable
Before switching on the implement
accessories that have accessories that have
opposite to the operator. ensure that it is not
suspension when suspension when
in contact with any objects.
been supplied or been supplied or
• Never operate the
attaching an extension attaching an extension
Keep your feet and hands
recommended by the
recommended by the
well away from the cylinder
implement without the
cable. cable.
and the ejector opening. Danger
manufacturer. The use of
manufacturer. The use of
attached collection bag or
• Never pull the cable to • Never pull the cable to
of injury!
alien parts results in the alien parts results in the
impact protector. Danger
disconnect the plug from disconnect the plug from
D
1. Place the implement on a level
immediate loss of all immediate loss of all
of injury! Always keep
the socket. Protect the the socket. Protect the
lawn surface.
guarantee claims.
guarantee claims.
2. Connect the power cable (17)
well away from the
cable from heat, oil and cable from heat, oil and
with the extension cable.
• Ensure that all nuts, bolts • Ensure that all nuts, bolts
ejector opening.
sharp edges 3. Form a loop in the end of the sharp edges
and screws are firmly and screws are firmly
power cable and hang it into the
• Do not operate the
• If the connecting cable is • If the connecting cable is
cable rain relief (18).
tightened and that the
tightened and that the
implement in the vicinity
4. Connect the implement to the
damaged, first disconnect damaged, first disconnect
implement is in a safe
implement is in a safe mains voltage.
of inflammable liquids or
the extension cable from the extension cable from
5. To switch on, press the unlocking
working state. working state.
gases as this could give button (1) on the handle and
the socket. You can then the socket. You can then
simultaneously press the starting
• Never try to repair the • Never try to repair the
rise to the danger of a fire
disconnect the connecting disconnect the connecting
lever (2). Release the unlocking
-
implement yourself, unless
implement yourself, unless
button (1).
or explosion.
cable of the equipment. cable of the equipment.
6. To switch off, release the starting
you have been trained
you have been trained
• Always disconnect the
lever (2).
accordingly. All work that accordingly. All work that
plug from the mains
Overload protection: The motor
has not been listed in has not been listed in
socket before any
is automatically switched off
these Instructions must
these Instructions must
when the implement is overloaded.
maintenance.
Release the starting lever and allow
only be carried out by
only be carried out by
the implement a cooling down period
authorised servicing authorised servicing of approx. 1 minute to reset.
st