Assembling The Handle Bar; Mounting And Emptying The; Collection Bag; Exchanging The Cylinder - FLORABEST FLV 1200 A1 Originalbetriebsanleitung

Work interruptions: Work interruptions:
agencies.
agencies.
• After the implement has • After the implement has

Assembling the handle bar

• Treat the implement with • Treat the implement with
been turned off, the been turned off, the
the greatest care. Always the greatest care. Always
cutting cylinder will cutting cylinder will
B
1. Insert the lower bar (7) into the
implement case (8) and screw
keep the tool clean for
keep the tool clean for
continue to rotate for a continue to rotate for a
it on with the two Philips screws
better and safer work.
better and safer work.
few seconds. Keep hands few seconds. Keep hands (22).
2. Use the screws and the wing nuts
Follow the maintenance Follow the maintenance
and feet well away. and feet well away.
(4b) to attach both central bars
instructions.
instructions.
(15) to the lower bar (7).
• Do not touch the spring • Do not touch the spring
3. Hang the cable strain relief (18)
• Never overload the
• Never overload the
tines before the implement tines before the implement
on the upper handle bar (3).
implement. Always work implement. Always work
4. Use the screws and the wing nuts
has been disconnected has been disconnected
(4a) to attach the upper bar (3) to
within the specified within the specified
from the mains and the from the mains and the
both central bars (15).
capacity range. Do not
capacity range. Do not
5. Fasten the machine cable (19)
spring tines have come to spring tines have come to
with the machine cable clip
use low-power machines
use low-power machines
a complete standstill. Risk a complete standstill. Risk
(12/16) to the bar.
for heavy-duty work. Do for heavy-duty work. Do
6. Attach the tool retainer (14) and
of injury owing to a sharp of injury owing to a sharp
clip the tool key (13).
not operate the implement not operate the implement
implement! implement!

Mounting and emptying the

for purposes for which it
for purposes for which it
• Only remove plant parts • Only remove plant parts

collection bag

is not intended.
is not intended.
when the implement is when the implement is
WARNING: Never operate the
standing completely still. standing completely still.
implement without the impact
Electrical safety: Electrical safety:
protector. Danger of Injury!
Ensure that the grass Ensure that the grass
ejector opening is clean ejector opening is clean Recommendation: Work with the
collection bag for aerating and
CAUTION! The
CAUTION! The
and free. and free.
without the collection bag for
following states how following states how
verticuting
• Switch off the power • Switch off the power
to avoid accidents and to avoid accidents and
Assembling the collection bag:
when the implement is to when the implement is to
The collection bag is delivered in a folded
injuries due to electric
injuries due to electric
be transported, lifted or be transported, lifted or
state and must therefore be assembled
shock:
shock:
before it is mounted on the implement.
tilted and when traversing tilted and when traversing
other surfaces than grass. other surfaces than grass.
C 1. Pull the collection bag over the
frame
• Before each use, carry • Before each use, carry
• Never leave the • Never leave the
2. Pull the collection bag's plastic
out a visual inspection of
out a visual inspection of
implement unattended at implement unattended at straps over the frame's rods
and clip them in.
the power and extension
the power and extension
(23).
the place of work. the place of work.
cables for signs of
cables for signs of
Children should be Children should be
Mounting the collection bag on the
damage or ageing.
damage or ageing.
supervised to ensure that supervised to ensure that
implement:
Damaged mains power Damaged mains power
they do not play with the they do not play with the
3. Lift the impact protector (6).
4. Push the pins on the collection
cables increase the risk of cables increase the risk of
appliance. appliance.
bag rods into the socket in the
electric shock.
electric shock.
• Always switch off the • Always switch off the implement case.
5. Release the impact protector so
• Connect the implement to
• Connect the implement to
implement and disconnect implement and disconnect
that it holds the collection bag (5)
a power socket with a a power socket with a
in its position.
the power plug: the power plug:
residual-current circuit residual-current circuit
- Whenever you leave the - Whenever you leave the
Removing and emptying the collection
breaker that has a rated
breaker that has a rated
bag:
implement implement
6. Lift the impact protector (6) and
current of not more than
current of not more than
- Before you clean the - Before you clean the
take out the collection bag (5).
30 mA. 30 mA.
ejector opening or ejector opening or

Exchanging the cylinder

• Always keep the • Always keep the
unblock or unclog the unblock or unclog the
Switch off the implement, disconnect
extension cable well
extension cable well
implement implement
the mains plug and wait until the
away from the cutting
away from the cutting
- When the implement is - When the implement is
cylinder is standing still.
tools. tools.
not being used not being used
Wear gloves when handling the
Should the power cable
Should the power cable
cylinder.
- During all maintenance - During all maintenance
become damaged during
become damaged during
and cleaning work and cleaning work
E 1. Turn the implement over.
work, then instantly
work, then instantly
2. Remove any grass or debris from
- When the power cable - When the power cable
either end of the mounted
disconnect the power disconnect the power
is damaged or has is damaged or has
cylinder to ensure no foreign
cable from the mains. DO
cable from the mains. DO
objects hinder reassembly.
become tangled become tangled
3. Take the spanner (
NOT TOUCH THE
NOT TOUCH THE
- When the implement - When the implement
the holder (
POWER CABLE BEFORE POWER CABLE BEFORE
4. Loosen the fastening screws and
hits an obstruction hits an obstruction
pull the bearing support
IT HAS BEEN IT HAS BEEN
during work or when during work or when
F
upwards.
DISCONNECTED FROM
DISCONNECTED FROM
5. Tilt the cylinder (
unusual vibrations arise. unusual vibrations arise.
upwards and pull the shaft out of
THE MAINS! Risk of
THE MAINS! Risk of
Establish the cause and Establish the cause and
the
electric shock. electric shock. 6. Insert the new cylinder (
see if the implement has see if the implement has
20/21) by reversing the
• If the power cable for this • If the power cable for this
been damaged. Do not been damaged. Do not
sequence.
equipment is damaged, it
equipment is damaged, it
repair it yourself! Have repair it yourself! Have
G
A
13) out of
A
14).
A
20/21)
square receptacle
B R I E
(24).
A
17