Troubleshooting; Specifications - Briggs & Stratton 080000 Bedienungsanleitung

1. Open the cover (B, Figure 17).
2. Remove the foam element (C, Figure 17).
3. Wash the foam element (C, Figure 17) in liquid detergent and water. Squeeze dry
the foam element in a clean cloth.
4. Saturate the foam element (C, Figure 17) with clean engine oil. To remove the excess
engine oil, squeeze the foam element in a clean cloth.
5. Install the foam element (C, Figure 17).
6. Close the cover (B, Figure 17).
Paper Air Filter
See Figure: 18
1. Open the cover (B, Figure 18).
2. Remove the filter (C, Figure 18).
3. Remove the pre-cleaner (E, Figure 18), if equipped, from the filter. To loosen debris,
gently tap the filter on a hard surface. If the filter is excessively dirty, replace with a
new filter.
4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air
dry. Do not oil the pre-cleaner.
5. Assemble the dry pre-cleaner, if equipped, to the filter.
6. Install the filter (C, Figure 18).
7. Close the cover (B, Figure 18).
Service Cooling System
WARNING
Running engines produce heat. Engine parts, especially muffler, become extremely
hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc., can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
NOTICE Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
1. Use a brush or dry cloth to remove debris from the air intake grille.
2. Keep linkage, springs and controls clean.
3. Keep the area around and behind the muffler, if equipped, free of any combustible
debris.
4. Make sure the oil cooler fins, if equipped, are free of dirt and debris.
After a period of time, debris can accumulate in the cylinder cooling fins and cause the
engine to overheat. This debris cannot be removed without partial disassembly of the
engine. Have a Briggs & Stratton Authorized Service Dealer inspect and clean the air
cooling system as recommended in the Maintenance Schedule.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Fuel Or Equipment With Fuel In Tank
• Store away from furnaces, stoves, water heaters or other appliances that have pilot
lights or other ignition sources because they can ignite fuel vapors.
Fuel System
See Figure: 19, 20
10
Note: Some models have a fuel tank for vertical storage that will let the engine tilt for
maintenance or storage (C, Figure 19). Do not store in vertical position with fuel tank filled
above the bottom of the fuel level indicator (D), if equipped. For further instructions, see
the equipment manual.
Store the engine level (normal operating position). Fill fuel tank (A, Figure 20) with fuel.
To allow for expansion of fuel, do not overfill above the fuel tank neck (B).
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits
to form in the fuel system or on essential carburetor parts. To keep fuel fresh, use Briggs
& Stratton Advanced Formula Fuel Treatment & Stabilizer, available wherever Briggs
& Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine if a fuel stabilizer is added according
to instructions. Run the engine for two (2) minutes to circulate the stabilizer throughout the
fuel system before storage.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil. See the Change Oil section. For
Just Check & Add™ models, an oil change is not required.

Troubleshooting

For assistance, contact your local dealer or go to BRIGGSandSTRATTON.com or call
1-800-233-3723 (in USA).

Specifications

Model: 80000
Displacement
Bore
Stroke
Oil Capacity
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
Model: 90000
Displacement
Bore
Stroke
Oil Capacity
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
Model: 093J00
Displacement
Bore
Stroke
Oil Capacity
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
7.63 ci (125 cc)
2.362 in (60 mm)
1.75 in (44,45 mm)
15 oz (,44 L)
.020 in (,51 mm)
180 lb-in (20 Nm)
.006 - .014 in (,15 - ,36 mm)
.004 - .008 in (,10 - ,20 mm)
.004 - .008 in (,10 - ,20 mm)
8.64 ci (140 cc)
2.495 in (63,4 mm)
1.75 in (44,45 mm)
15 oz (,44 L)
.020 in (,51 mm)
180 lb-in (20 Nm)
.006 - .014 in (,15 - ,36 mm)
.004 - .008 in (,10 - ,20 mm)
.004 - .008 in (,10 - ,20 mm)
9.15 ci (150 cc)
2.583 in (65,60 mm)
1.75 in (44,45 mm)
15 oz (,44 L)
.020 in (,51 mm)
180 lb-in (20 Nm)
.006 - .014 in (,15 - ,36 mm)
.004 - .008 in (,10 - ,20 mm)
.004 - .008 in (,10 - ,20 mm)
BRIGGSandSTRATTON.com