Maintenance - Ryobi CAG-180 Bedienungsanleitung

GB
FR DE ES
OPERATION
OPERATING THE GRINDER (Fig. 10)
Always carefully select and use grinding wheels that are
recommended for the material to be ground. Make sure
that the minimum operating speed of any accessory
wheel selected is 6,500 r/min. or more. The grinding
wheel provided with the grinder is suitable for grinding
welds, preparing surfaces to be welded, grinding
structural steel, and grinding stainless steel.
To operate the grinder
Secure all work in a vise or clamp to a workbench.
Q
DANGER
Never use the grinder with the guard removed.
It has been designed for use only with the guard
installed. Attempting to use grinder with guard
removed will result in loose particles being
thrown against the operator resulting in serious
personal injury.
Hold the grinder in front and away from you with
Q
both hands, keeping the grinding wheel clear of the
workpiece.
Turn on the grinder and let the motor and grinding
Q
wheel build up to full speed.
Lower the grinder gradually until the grinding wheel
Q
contacts the workpiece.
Keep the grinder tilted at an angle from 5° to 15°.
Q
WARNING
o prevent loss of control and possible serious
personal injury, always operate the grinder
with both hands, keeping one hand on the side
handle.
Move the grinder continuously at a steady, consistent.
Q
CAUTION
If the grinder is held in one spot too long, it will
gouge and cut grooves in the workpiece. If the
grinder is held at too sharp an angle, it will also
gouge the workpiece because of concentration of
pressure on a small area.
Use just enough pressure to keep the grinder from
Q
chattering or bouncing.
NOTE: Heavy pressure will decrease the grinder's speed
and put a strain on the motor. Normally the weight of the
tool alone is adequate for most grinding jobs. Use light
pressure when grinding jagged edges or loose bolts
where there is the potential for the grinder to snag on the
metal edge.
Lift the grinder away from the workpiece before
Q
turning off the grinder.
IT NL PT DK SE FI NO RU PL CZ
English

MAINTENANCE

WARNING
When servicing, use only identical replacement
parts. Use of any other parts may create a
hazard or cause product damage.
WARNING
Always wear safety goggles or safety glasses
with side shields during power product operation
or when blowing dust. If operation is dusty, also
wear a dust mask.
WARNING
To avoid serious personal injury, always remove
the battery pack from the product when cleaning
or performing any maintenance.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
REPLACING THE GUARD (Fig. 5)
CAUTION
After extended use, the guard may wear and
need replacing. If you drop the grinder and
damage the guard it may also be necessary for
you to replace it.
To replace the guard:
Remove the battery pack from the grinder.
Q
Depress spindle lock and rotate clamp nut until
Q
spindle locks.
Loosen and remove clamp nut from spindle using the
Q
wrench provided.
Remove grinding wheel and disc flange.
Q
Unlock the guard clasp by pulling the clasp out, away
Q
from the grinder. Remove guard.
Place the new guard on the shoulder of the bearing
Q
cap.
Rotate guard to the correct position. Refer to
Q
Positioning the Guard earlier in this manual.
NOTE: Be sure the raised ridge on the guard is seated in
the groove on the bearing cap.
Reassemble disc flange, grinding wheel, and clamp
Q
nut. Refer to Installing Grinding Wheel earlier in this
manual.
5
HU RO LV LT EE HR SI SK GR TR