Siemens SINUMERIK 840DE sl Bedienhandbuch Seite 11
Hmi sl drehen
Vorschau ausblenden
Andere Handbücher für SINUMERIK 840DE sl:
- Diagnose-handbuch (1550 Seiten) ,
- Funktionshandbuch (1026 Seiten) ,
- Bedienhandbuch (826 Seiten)
Inhaltsverzeichnis
Werbung
7.16
Ab-/Anfahrzyklus programmieren ..............................................................................................201
7.17
Messzyklenunterstützung ..........................................................................................................203
8
Technologische Funktionen programmieren (Zyklen) ............................................................................ 205
8.1
Bohren........................................................................................................................................205
8.1.1
Allgemeines................................................................................................................................205
8.1.2
Zentrieren (CYCLE81) ...............................................................................................................206
8.1.3
Bohren (CYCLE82) ....................................................................................................................208
8.1.4
Reiben (CYCLE85) ....................................................................................................................209
8.1.5
Tieflochbohren (CYCLE83)........................................................................................................211
8.1.6
Ausdrehen (CYCLE86) ..............................................................................................................214
8.1.7
Gewindebohren (CYCLE84, 840) ..............................................................................................216
8.1.8
Bohrgewindefräsen (CYCLE78).................................................................................................220
8.1.9
Positionen und Positionsmuster.................................................................................................223
8.1.10
Beliebige Positionen (CYCLE802) .............................................................................................224
8.1.11
Positionsmuster Linie (HOLES1) ...............................................................................................227
8.1.12
Positionsmuster Kreis (HOLES2)...............................................................................................229
8.1.13
Positionen wiederholen..............................................................................................................231
8.2
Drehen .......................................................................................................................................233
8.2.1
Allgemeines................................................................................................................................233
8.2.2
Abspanen (CYCLE951) .............................................................................................................233
8.2.3
Einstich (CYCLE930) .................................................................................................................236
8.2.4
Freistich Form E und F (CYCLE940).........................................................................................239
8.2.5
Gewindefreistiche (CYCLE940) .................................................................................................241
8.2.6
Gewindedrehen (CYCLE99) ......................................................................................................244
8.2.7
Gewindekette (CYCLE98)..........................................................................................................253
8.2.8
Abstich (CYCLE92)....................................................................................................................256
8.3
Konturdrehen .............................................................................................................................258
8.3.1
Allgemeines................................................................................................................................258
8.3.2
Darstellung der Kontur ...............................................................................................................259
8.3.3
Neue Kontur anlegen .................................................................................................................260
8.3.4
Konturelemente erstellen ...........................................................................................................262
8.3.5
Kontur ändern ............................................................................................................................267
8.3.6
Konturaufruf (CYCLE62) - nur bei G-Code-Programm..............................................................268
8.3.7
Abspanen (CYCLE952) .............................................................................................................269
8.3.8
Abspanen Rest (CYCLE952) .....................................................................................................273
8.3.9
Stechen (CYCLE952) ................................................................................................................275
8.3.10
Stechen Rest (CYCLE952) ........................................................................................................277
8.3.11
Stechdrehen (CYCLE952) .........................................................................................................279
8.3.12
Stechdrehen Rest (CYCLE952).................................................................................................282
8.4
Fräsen ........................................................................................................................................284
8.4.1
Planfräsen (CYCLE61) ..............................................................................................................284
8.4.2
Rechtecktasche (POCKET3) .....................................................................................................287
8.4.3
Kreistasche (POCKET4) ............................................................................................................291
8.4.4
Rechteckzapfen (CYCLE76)......................................................................................................296
8.4.5
Kreiszapfen (CYCLE77).............................................................................................................299
8.4.6
Mehrkant (CYCLE79).................................................................................................................302
8.4.7
Längsnut (SLOT1) .....................................................................................................................304
8.4.8
Kreisnut (SLOT2) .......................................................................................................................308
8.4.9
Offene Nut (CYCLE899) ............................................................................................................312
8.4.10
Langloch (LONGHOLE) - nur bei G-Code-Programm ...............................................................319
8.4.11
Gewindefräsen (CYCLE70) .......................................................................................................321
8.4.12
Gravur (CYCLE60).....................................................................................................................324
HMI sl Drehen
Bedienhandbuch, 06/2009, 6FC5398-8CP20-0AA0
Inhaltsverzeichnis
11
Werbung
Inhaltsverzeichnis
